Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Refer to Figure 1. • A straight, short vent run will allow the hood to perform more efficiently. • Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. • Temporarily wire the hood to test for proper operation before installing. • Important: Peel protective film off the hood, if any. • Use duct tape to seal joints between pipe sections. • For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not provided) on each side. Refer to Figure 2. • Using references in TABLE 1 and Measurements and Diagrams on page 18, create access opening for electrical wires and hood exhaust under the cabinet. Hood Installation CAUTION: If moving the cooking range is necessary to install the hood, turn off the power on an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 1. Puncture the knockout holes (for mounting under the cabinet) on the hood as shown in Figure 3. 2. If necessary, attach two rubber stands (provided) with 3M adhesive tapes (provided) to the back corners of the hood. 3. Using references in TABLE 1 and Measurements and Diagrams on page 18 center the hood beneath the cabinet and flush with the front of the cabinet. Figure 1 Figure 2 . Figure 3 6 4. Draw electrical wires through cabinet Figure 4 access opening. 5. From inside of the hood, place screw (not provided) into the exact center of each knockout hole and secure to cabinet bottom. Once all mounting screws are in place, finish tightening screws until secure. CAUTION: MAKE SURE THE HOOD IS SECURE BEFORE RELEASING. 6. For safety purpose, pre-drilled mounting holes are provided through the back of the hood. For a more secure installation, use as many mounting holes as needed to secure Figure 5 from the inside of hood (screws not provided). Ductwork Installation 7. Use 7” round steel pipe (follow building codes in your area) to connect the exhaust on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer to Figure 4. Wiring to Power Supply SAFETY WARNING RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. 8. Connect the electrical wires. -Connect three wires (black, white and green) to house wires and cap with wire connectors. Connect according to color: black to black, white to white, and green to green as shown in Figure 5. -Store wires in the wiring box. Figure 6 7 Accessories Accessories Figure 7 9. Drop oil tunnel into recess support near rear of hood. Refer to Figure 6. 10. Install baffle filters and stainless spacer(s). Refer to Measurements and Diagrams on page 22 for baffle filter and stainless spacer placement. Angle baffle filter toward back of hood . Push baffle filter up until almost level . Slide forward into recess behind the front of hood . Lower baffle filter . Slide back until it fits into resting position . Refer to Figure 7. 11. Repeat step 10 to install all baffle filters and stainless spacer(s). Final Assembly 12. Turn power ON in control panel. Check all light and fan operation. 13. Make sure to leave this manual for the homeowner. 8 STAND ALONE INSTALLATION *** This installation only applies if installing with the CH1120DC duct cover. Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. • Decide the location of the venting pipe from the hood to the outside. (Figure 8) • A straight, short vent run will allow the hood to perform more efficiently. • Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. • Temporarily wire the hood to test for proper operation before installing. • Important: Peel protective film off the hood and duct covers, if any. • Use duct tape to seal joints between pipe sections. • If necessary, prepare back wall frame with cross framing lumber for secure installation. • Using references in TABLE 2 and measurements on pages 19-21, determine the level of the lumber. (Figure 9) Hood Preparation before Installation • If necessary, attach two rubber stands (provided) with 3M adhesive tapes (provided) to the back corners of the hood. • Attach the outer duct cover-mounting bracket {K} (provided) to the hood- mounting bracket {F} (provided) with two (3/16” x 1/2”) screws (provided) as shown in Figure 10. • Attach the hood-mounting bracket {F} to the back of the hood with six (3/16” x 1/2”) screws (provided) as shown In Figure 11. Figure 8 Figure 9 Figure 10 Figure 11 Hood Installation CAUTION: If moving the cooking range to install the hood is necessary, turn off the power on an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 9 1. Using...
Otros modelos de este manual:Los aficionados - CH7636SQB (1.34 mb)
Los aficionados - CH7642SQB (1.34 mb)
Los aficionados - CH7630SQB (1.34 mb)