Votos - , Puntuación media: ( )

Manual de usuario Kobe Range Hoods, modelo CH0130SQB

Fabricar: Kobe Range Hoods
Tamaño del archivo: 678.7 kb
Nombre del archivo: 882402b6-594b-4f08-9b68-3e300b33b6f3.pdf

Idioma del manual:

El documento se está cargando, por favor, espere

Descargar ahoraCerca

El documento se está cargando, por favor, espere

Descargar ahoraCerca

Refer to Figure 12. Figure 11 Hood Installation CAUTION: If moving the cooking range is necessary to install the hood, turn off the power in an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 1. Using references in Table 2 and Measurements and Diagrams on pages 19-20, mark the leveling point of the hood. Position two mounting screws (not provided) on the wall, leaving 1/8” away from the wall. Refer to Figure 13 Figure 12 9 2. Align hood-mounting bracket to the two screws on the wall and hook hood into place. Tighten screws to secure hood to the wall. 3. For safety purpose, extra knockout holes on the back of the hood are provided for a more secure installation. Knock out as many holes as needed and secure with screws (not provided) from the inside of hood. CAUTION: MAKE SURE HOOD IS SECURE BEFORE RELEASING. WALL Figure 13 Wiring to Power Supply SAFETY WARNING TO PREVENT THE RISK OF ELECTRICAL SHOCK OR INJURY, THIS RANGE HOOD SHOULD BE PROPERLY GROUNDED AND INSTALLED BY A TRAINED PROFESSIONAL WHO IS KNOWLEDGEABLE ABOUT APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. 4. Connect the electrical wires. Figure 14 -Connect three wires (black, white and green) to house wires and cap with wire connectors. Connect according to color: black to black, white to white, and green to green as shown in Figure 14. -Prevent wires from slipping between motor and any moving parts by securing in electrical box. 10 11 Duct Cover Installation 5. Use 8” aluminum or steel pipe (follow building codes in your area) to connect the ducting transition on the hood to the ductwork above. Use duct tape to seal and secure joints as shown in Figure 15. Slide the duct cover onto the hood. 6. Use 3/16” x 3/8” screws (provided) to attach duct cover to hood. Figure 15 Final Assembly CAUTION: Install heating lamps last. 7. Drop Oil Tunnel into support structure. Refer to Figure 7. 8. Angle baffle filter toward back of hood . Refer to Figure 8. 9. Push baffle filter up until almost level . 10. Slide forward into recess at front of hood . 11. Lower baffle filter and slide back until it fits into resting position . 12. Repeat for all baffle filters and spacers. Refer to Measurements and Diagrams on page 21 for baffle filter and stainless spacer arrangement. 13. Install heating lamps (not provided), 120 Volts 250 Watts max. each. 14. Turn power ON in control panel. Check all lights and fan operation. 15. Make sure to leave this manual for the homeowner. Figure 16 Figure 17 OPERATING INSTRUCTIONS This KOBE hood is equipped with touch-sensor screen and features 3 minute delay shutoff, powerful centrifugal squirrel cage with baffle filters, bright 12-volt 20-watt halogen lights and heating lamp capability (heating lamps not included). The touch-sensor screen has Heat Lamp Control, Light Control, Speed Control (QuietMode™, Low, Medium and High), and Power Control. Refer to Figure 18. Power ControlLight Control Speed ControlHeat Lamp Figure 18 Power Control • ••••Once power is supplied to the KOBE hood, the sign will light up and remain lit as long as power is supplied to the hood. • ••••To activate, gently touch the symbol under the Power Control sign. The remaining control signs will light up and is ready for function choice. • ••••You can turn hood off immediately or after a 3 minute delay. Turn Off Immediately Gently tap the symbol under the Power Control sign twice, the range hood will turn off immediately leaving only the sign lit. 12 Turn Off After 3 Minute Delay Gently touch the symbol under the Power Control sign once, the symbol flashes and after 3 minutes, the hood will turn off leaving only the sign lit. Speed Control: • There are four speeds: QuietMode™, Low, Medium, and High. To activate the speed, touch the control under the speed sign. For example, if turning on hood at low speed, gently touch the symbol under the sign. If you want to switch from low to high speed, touch the symbol under the sign and the hood change to high speed. To turn off only speed control (if, for example, halogen lights are also on), touch the symbol under the sign. Light Control • ••••Gently touch the symbol under the sign once to turn on the light. Touch the symbol again to dim the lights. Touch the symbol a third time will turn off the halogen lights. Heating Lamp Control • ••••Gently touch the symbol under the sign once to turn on the heat lamps. Touching the symbol under the sign again will turn off heat lamps. 13 MAINTENANCE SAFETY WARNING NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN WHILE THE FAN IS OPERATING. For optimal operation, clean range hood surface and stainless steel baffle filters regularly. Cleaning Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. Regular care will help preserve the appearance of the hood. 1) Use only mild soap or detergent solutions. Dry surfaces using soft clo...