Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
4-2. To connect the wires, hold the bare metal leads together and place a wire nut over them, then twist clockwise until tight. 4-3. Connect the wires as follows: • Connect the green ground wire from the fan to the ground wire from the ceiling • Connect the white wire from the fan to the common wire from the ceiling • Connect the black wire and the black and white striped wire from the fan to the black wire from the ceiling CAUTION: Be sure no bare wire or wire strands are visible after making connections. 4-4. Push all wires and wire nuts back through the ceiling plate hole into the outlet box. Step 4-3 Wire Nut 5 • Installing the Canopy and Canopy Trim Ring 5-1. Holding the canopy, raise the fan off the hook. 5-2. Align the slots in the canopy with the tabs on the ceiling plate. 5-3. Raise the canopy over the ceiling plate. Rotate the canopy clockwise until the tabs on the ceiling plate totally engage with the slots in the canopy. 5-4. Loosely assemble the three canopy screws into the canopy one at a time. Once all three screws are in, tighten them. 5-5. Using both hands, push the canopy trim ring up to the top of the canopy. .e canopy trim ring will snap and lock into place. Step 5-2 Ceiling Plate Canopy Trim Ring Canopy Should you need to remove the canopy trim ring, follow these steps: 1. Locate the tab indicators, small bumps on top of tabs. 2. Press firmly on opposite sides of the ring towards the canopy. .e tabs will flex out releasing the trim ring from the canopy. Step 5-3 Steps 5-4 – 5-5 Canopy Screw 6 • Assembling the Blades Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. 6-2. Install three blade assembly screws through the the blade iron and blade, into the medallion. If you used grommets, the blades may appear slightly loose after screws are tightened. .is is normal. 6-3. Remove the blade armature screws and rubber shipping bumpers from the motor. Save the screws for the following step and discard the shipping bumpers. 6-4. For each blade, insert one blade armature screw through the blade iron, and attach loosely to the fan. Insert the second blade armature screw, then securely tighten both armature screws. Step 6-4 Steps 6-1 – 6-2 Blade Assembly Screws Blade Armature Screw 7 • Installing the Switch Housing 7-1. To attach the upper switch housing, partially install two #6-32 x 3/8” housing assembly screws into the switch housing mounting plate. 7-2. Feed the upper plug connector through the center opening of the housing. 7-3. Align the keyhole slots in the housing with the housing assembly screws. 7-4. Turn the housing counterclockwise until the housing assembly screws are firmly situated in the narrow end of the keyhole slots. Install the remaining #6-32 x 3/8” screw into the housing. Tighten all three screws firmly. Steps 7-1 – 7-3 Housing Assembly Screw Upper Switch Housing Step 7-4 8 • Setting the Remote Transmitter and Receiver Setting Jumper Switches When two or more fans are located near each other, you may desire to have the receiver/transmitter for each fan set to a different code, so that the operation of one fan does not affect the operation of the other fans. In the transmitter you can access the jumpers from the battery compartment. .e jumpers are very small. You can move them most easily using a small pair of pliers or tweezers. IMPORTANT! Before you change jumper switches, make sure the battery is not connected to the transmitter. You must now set the jumper switches in the remote transmitter and receiver so that they match. 8-1. Change the position of the jumper switches in the transmitter and the receiver. Be sure the position of the jumper switches matches. If they don’t match, the controller will not function. For instructions on how to set the jumper switches, read the box below. 8-2. Install the included 12-volt battery into the transmitter. CAUTION: .e remote control device complies with part 15 of the FCC rules. Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment. Operation is subject to the following two conditions: 1. .is device may not cause harmful interference. 2. .is device must accept any interference received, including interference that may cause undesired operation. WARNING: Maximum fan load is 1 Amp; maximum lamp is 100 Watts. Do not use any speed control with this product. 9 • Completing Your Installation 9-1. To attach the lower switch housing, connect the plug connector from the motor to the plug connector from the receiver in the lower switch housing assembly. Note: Both plug connectors are polarized and will only fit together one way. Make sure the connectors are properly aligned before connecting them. Incorrect connection could cause improper operation and damage to the product. 9-2. Place the lower switch housing assembly o...