Iniciar sesión:
Votos - 4, Puntuación media: 5 ( )

Manual de usuario Air King, modelo 9130

Fabricar: Air King
Tamaño del archivo: 68.18 kb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


(Figure 4-Detail A) New 3/04 OPERATING INSTRUCTIONS 1.)TO OPERATE: Plug cord into a grounded 120V, 60 Hz outlet. Select desired operating speed with pull cord on the rear of the motor: First pull: High Second pull: Medium Third pull: Low Fourth pull: OFF NOTE: This fan is very heavy. Failure to securely hold onto head assembly while adjusting head height or head angle could result in personal injury. 2.)TO ADJUST HEAD ANGLE: While holding head firmly, loosen knob under motor (turn counterclockwise). Tilt head to desired position FIRMLY retighten knob under motor. 3.)TO ADJUST HEAD HEIGHT: While holding upper column firmly, loosen set screw on column collar (turn counterclockwise). Raise or lower head to desired position. FIRMLY retighten set screw. NOTE: Motor Head Adjustment Knob, On/Off Pull Cord and Set Screw Placement have the same location on oscillating or nonoscialling models. - NEVER use maintenance, should be performed by an authorized service representative. Call 1-800-233-0268, Monday through Friday, between the hours of 8:00 a.m.and 5:00 p.m. for the location of your nearest service center. LUBRICATION: Precision bearings are sealed at the factory for life and do not require further lubrication. STORAGE: Store the Fan, with these instructions, in a clean and dry place. 3 5084415 justment Knob over the remaining threads. COLUMN TO BASE ASSEMBLY 1. Rest Column and Head Assembly on floor next to the Base As- sembly. Tilt Base Assembly up on end. Pick up Lower Pipe of Column and insert bottom of Pipe into the Mounting Flange. 2. Tilt entire Assembly (base and head) upright. Confirm that the column is fully seated in Mounting Flange. Insert and securely tighten the 3/8"-16 x 3/4" Allen Set Screw in Mounting Flange with the Allen Wrench (supplied in parts bag). Make sure Screw is fully tightened and there is NO looseness between Column and Mounting Flange. 6. The bottom most Hooks will require the use of a flathead screw- driver to complete assembly. Stand behind Fan. Slip the flat of the blade between the front and rear grills, next to one of the unfastened hooks. (Figure 4-Detail B) Pull screwdriver handle upwards towards the rear grill. Slip the front grill hook over the rear grill outer ring with a push. Repeat procedure with remaining Hooks. Caution: Be careful not to bend any wires on grills or pinch your hands during assembly. 7. Attach pull cord to pull chain. Fan assembly is now complete. Re- fer to sections below for correct operating instructions and main- tenance. NOTE FOR OSCILLATING MODELS: FAN IS SHIPPED WITH 90. OSCILLATION ANGLE, FOR 45. OSCILLATION ANGLE, CON- NECT THE OSCILLATION LINK TO THE INNERMOST HOLE IN THE CAM GEAR. Oscillating Model Detail A Top Hooks Detail B Bottom HooksFigure 4Figure 3 Figure 3 Figure 4 Detail B Bottom Hooks Detail A Top Hooks Non-Oscillating Model MAINTENANCE WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING OR SERVICING. WARNING: DO NOT IMMERSE FAN IN WATER! CLEANING: Use a soft cloth and mild so...

Otros modelos de este manual:
Los aficionados - 9124 (68.18 kb)
Los aficionados - 9125 (68.18 kb)
Los aficionados - 9135 (68.18 kb)
Los aficionados - 9171 (68.18 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría