Votos - 4, Puntuación media: 4.8
(
)
)
|
Resumen del manual
Description of the Appliance • The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. • The hood is supplied as an extractor unit and can also be used in a recirculation mode by fitting one charcoal filter (available from your local Service Force Centre). Extractor version • In this version fumes are extracted to the outside via a hose. • In order to obtain the best performance the hose should have a diameter equal to the outlet hole. Recirculation Version • The air is filtered through a charcoal filter and returned to the kitchen. • You will need an original AEG charcoal filter for the recirculation function. (Available from your local Service Force Centre). • Insert the charcoal filter into the lugs of the frame above using the 2 red lugs E to retain it, press the red lugs inwards, and insert the charcoal filter in the frame. Fig. 1. E EE Fig. 1 Hood Operation • Best results are obtained by using a low speed for normal conditions and high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking then you will get an underpressure in the kitchen. It should be left on after cooking for about 15 minutes or until all odours have disappeared. The control switches are located on the unit’s front panel: Intensive speed Light switch Motor switch The hood is also equipped with a micro-switch which can be found under the lower runner of the visor on the right hand side. With this micro-switch, the appliance may be automatically switched on and off by opening and closing the pull-out panel, but only if the fan speed has already been set and the light button is turned to “I”. Maintenance and care • The hood must always be disconnected from the electricity supply before beginning any maintenance work. • Never insert pointed objects in the motor’s protective grid. • Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. • Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. • It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. ON OFF Metal grease filter • The purpose of the grease filters is to aspirate grease particles which form during cooking and it must always be used, either in the external evacuation or internal recycling function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Open the metal grease filter • Model CHDE 6260:To remove the grease filters, first pull the handles upwards, then extract the filter outwards. Fig. 2a. • Model 335 D:To remove the grease filters, first remove the grid (see Fig. 2a) and take out the grease filters oushing on the locking springs Z. Fig. 2b. Hand washing Soak grease filters for about one hour in hot water with a grease- loosening cleaner, then rinse off thoroughly with hot water. Repeat the process if necessary. Refit the grease filters when they are dry. Dishwasher Place grease filters in the dishwasher. Select most powerful washing programme and highest temperature, at least 65°C. Repeat the process. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance. • Clean the inner housing using a hot detergent solution only (never use caustic detergents, abrasive powders or brushes). Z Fig. 2a Fig. 2b Charcoal filter • The charcoal filter should only be used if you want to use the hood in the recirculation function. • To do this you will need an original AEG charcoal filter (available from your local Service Force Centre). • The charcoal filter cannot be washed nor regenerated. The charcoal filter should be replaced every 12 months under normal use. Replacement filters are available from your local Service Force Centre. Fitting the charcoal filter: Insert the charcoal filter into the lugs of the frame above using the 2 red lugs E to retain it, press the red lugs inwards, and insert the charcoal filter in the frame. Fig. 3. • Removing: Press both red lugs E upwards (towards the inside of the housing) and remove the charcoal filter downwards. Bild. 3. • Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the registration plate located on the inside of the unit. • The charcoal filter can be ordered from your local Service Force Centre. E EE Fig. 3 • • Warning Failure...
Otros modelos de este manual:Los aficionados - CHDE 6260 (358.29 kb)
Los aficionados - DE 6260 (358.29 kb)