Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Rotate motor upwards until it snaps into the spring clip on the right. Secure the motor to the hood with the machine screw and lock washer. Plug connector into the motor, Fig. 11. From Control Panel Motor connector FIG. 11 FIG. 10 Spring Clip Outlet Bracket Motor Connector Spring Clip Motor support Fixing point Fixing point Bracket Integral ventilator for 40" Hood 11 INSTALLATION 12 2. Snap the central baffle filter panel into the place so the both rails engage with side pins on both sides of hood. Drive 2 screws (1 on each side ) through baffle filter panel hole to hood. See Fig. 12. 3. Snap four-side baffle trim to hood (4 pins engage each side trim). The baffle trims are supplied separately (for IVS52 only). See Fig. 13. 4. Install all baffle filters as per Use and Care Manual instructions. Fixing screw location Fig. 12 Fig. 13 Baffle filter panel Baffle trim INSTALLATION WIRING TO POWER SUPPLY WARNING: Turn off power circuit at the service panel before wiring this unit. 120 VAC, 15 Amp circuit required. 1. Remove j-box cover as shown in Fig. 14. 2. Remove the knockout and install the strain relief (conduit) connector (1/2") in junction box. 3. Run 3 wires; black, white and green (#14 AWG) in 1/2" conduit from service panel to junction box. 4. Connect black wire from service panel to black or red in junction box, white to white and green to green-yellow. See Fig. 14. 5. Close junction box cover. 6. Plug cable at the top of the hood into the junction box connector. 7. Check all light bulbs to make sure they are secure in their sockets, then turn power on in service panel and check lights and blower operation per Care & Use manual and install drip tray support and filters. From Control Panel Junction Box 1/2" Conduit Junction Box Cover FIG. 14 13 INSTALLATION FINAL ASSEMBLY For final Chimney Cover installation, DO NOT USE ELECTRIC SCREW DRIVER. NOTE: Overtightening screws can deform metal. 1. Install the cage nuts from inside the rectangular slots supplied with top and bottom duct covers. See Fig. 15. A total of 14 nuts must be fitted. x Duct cover Top section Duct cover bottom section Duct cover Top section Duct cover bottom section Duct cover Top section FIG. 15 14 15 INSTALLATION 2. Install the two brackets to the chimney structure supplied with the kit by using one screw each side. 3. Join the two top sections of the duct cover. Screw the two sections together with 8 screws (4 each side- see the top view in Fig. 16 for joining the two sections). 4. Install the top duct cover assembly to the bracket, near the ceiling, with two screws (one each side). Bracket Duct cover Top section Duct cover Top section Bracket Screw Fix to the top Top Duct assembly Diagram Drive a #10 x 2-1/4" screw into wood framing above ceiling. This screw supports the load of the upper chimney duct cover. One screw each side. FIG. 16 16 INSTALLATION 5. Join the two bottom sections of the duct cover which covers the chimney structure using 6 screws, (3 each side, see Fig. 17 for the plan diagram for joining the two sections). 6. Insert the bottom section of the duct cover in its seat so that it completely covers the chimney structure. 7. Install the 4 supplied trims for duct cover channels to cover the fasteners of the bottom duct covers. (CAUTION! THE BOTTOM FLUE TRIMS ARE THE NARROWER AND SHALLOWER ONES). The wider and deeper trims are those used for the top flue, and must be cut to size. If necessary, slightly expand the trims to ensure their adherence to the flue. 8. Turn the power on again at the electrical panel and check for correct hood operation. 9. Make sure to leave this manual for the home owner. Duct cover Rear Bottom section Duct cover Front Bottom section Bottom Duct assembly Diagram Screw X X Tabs FIG. 17 HOW TO OBTAIN SERVICE BEFORE YOU CALL FOR SERVICE n Is the circuit breaker tripped or the fuse blown? n Is there a power outage in the area? For warranty service, contact DCS Customer Care Representative at (888) 281-5698. Before you call, please have the following information ready: ¦ Model Number (located on the inside of the top panel on the left, behind the rear back filter, above the motor assembly) ¦ Serial Number (located on the inside of the top panel on the left, behind the rear back filter, above the motor assembly) ¦ Date of installation ¦ A brief description of the problem Your satisfaction is of the utmost importance to us. If a problem cannot be resolved to your satisfaction, please call, write or email us at: Write: Fisher & Paykel Appliances, Inc. Attention: DCS Customer Care 5900 Skylab Road Huntington Beach, CA 92647 email: support@dcsappliances.com 17 WARRANTY LIMITED WARRANTY When you purchase a new DCS Ventilation Product for personal or consumer use you automatically receive a One year Limited Warranty covering parts and labor for the entire product, and a Five year Limited Warranty on the switches and motor (parts only) for servicing within the 48 mainland United States, Hawaii, Washington D.C...