Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
• Care should be taken when servicing the light panel due to a shortswitch wire. WARNING All electrical work must be done in accordance with local and/or national electrical codes as applicable. For safety, this product must be earthed. If you are unfamiliar with methods of installing electrical wiring, employ the services of a qualified electrican. Turn off power at service entrance before installing wiring or servicing this product. The canopy is heavy, overall weight 65 lbs (29kg). Please ensure adequate care when installing the canopy to prevent personal injury. The canopy must be installed onto a solid wall or solid studs. NOTE: Stainless steel and iridium is very easily damaged during installation if abraided or knocked by tools. Read the instructions before starting the assembly. Remove the filters to allow access to wall mounting holes. The unit is designed for 2290 to 2690mm (7’ 6” to 8’ 10”) high ceilings. The chimney is telescopic and is designed for 615 to 895mm (24~3/16” to 35~1/4”) adjustment. Ascertain the desired installation height of the canopy. NOTE: Installation height ranges from 610 to 760mm (24” to 30”). DUCTING: Ducting accessories are not supplied. The air outlet from the motor requires 150mm (6”) round ducting which requires 160mm (6~5/16”) diameter hole in the ceiling. lbs lbs Ceiling height 2290 to 2690mm (7’6” to 8’10”) Installation height 610 to 760mm (24” to 30”) Cooking surface 914mm (36”) P R E - I N S T A L L A T I O N I N S T A L L A T I O N O F U N I T This appliance must be positioned so that the electrical plug is accessible. Care and attention should always be taken when cooking with oils, alcohol, etc, which give off flammable vapours. Pre-used oil is especially dangerous in this respect. Do not use an uncovered electrical grill. Particular care must be taken with grease filters which must be periodically cleaned, at least every two months. Remove the grease filters and wash them either by hand or in the dishwasher using mild detergent. Use lukewarm water and mild detergent to clean stainless steel/iridium components. In high humidity and coastal environments, cleaning should be carried out frequently. CAUTION: Never use abrasive or oil based liquid cleaners. INSTALLING MOUNTING BRACKET Align the centre of the installation bracket with the centre of the cooking surface (recommend to use plumb bob). Place the flat/horizontal surface of the mounting bracket 215mm (8~1/2”) above the installation height (dia.1). Ensuring the mounting bracket is level, mark and drill the holes in the wall. Use the screws and plugs provided to attach bracket. INSTALLING CHIMNEY BRACKETS Cut cornice to suit the chimney cover. Align the centre of the chimney bracket with the centre of the cooking surface. Mark and drill the holes in the wall and ceiling. Use appropriate mounting screws or anchors. INSTALLING THE CHIMNEY A rubber extrusion has been provided to hide any irregularities between the chimney and the canopy/ceiling, it is fitted by simply pushing it over the top and bottom visible edges of the chimney. This steel edge may be sharp so care must be taken to avoid damage to fingers. If desired this extrusion may be omitted from the assembly. Remove the protective plastic film from the chimney. Prior to mounting the chimney, determine the height required on the chimney. The height can be adjusted by changing the screw on the back lip (dia.2). Do not tighten the screws because the chimney needs to slide up when installing the canopy. Mount the chimney to the ceiling bracket using the screws provided . INSTALLING THE CANOPY Ensure the filters are removed from the canopy. Hang the canopy onto the installation bracket. Align the canopy so it is central to the cooking surface and lines up with the chimney cover. Mark out the position of the two safety screw holes located on the back panel. Remove canopy, drill the safety screw holes and fit wall plugs. Refit the canopy to the wall and secure using the appropriate mounting screws (dia.3). Remove protective plastic film from the canopy and filters. Refit the filters to the canopy. 215mm dia.1 installation height 215mm cooking surface dia.2 dia.3 C A N O P Y O P E R A T I O N Thank you for purchasing a quality stainless or iridium canopy rangehood. We have a high standard of quality control and each rangehood is tested and approved before it leaves the factory. IMPORTANT : Please read prior to installation and operation. • Always switch the power off prior to installing, servicing or cleaning the appliance. • Remove transport tape from the lights and filters before use. • Never use the appliance without the filters. • Please read the notes on general cleaning, especially the filters. • Exhaust air must not be discharged into a heating flue or wall cavity, unless the cavity is designed for that purpose. • Areas where the rangehood is installed that also have gas, oil or coal fired heaters, must be well ventilated to prevent a partial vacuum in t...
Otros modelos de este manual:Los aficionados - 88795 (217.18 kb)