Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
1363 Part 4, is a recommended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions. Any permanent electrical installation must comply with the latest I.E.E. Regulations and local electricity board regulations. For your own safety this should be undertaken by a qualified electrician or competent person e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). This appliance conforms to BS.800:1988 and EEC Directive No 87.308 regarding suppression of radio and television interference. DUCTING FITTING The cooker hood should be ducted to the outside. Fit the blanking plate supplied into the aperture that is not going to be used. The ducting spigot must be fitted into the aperture and sealed to form an air tight connection. To fit the ducting spigot and blanking plate align the interlocking lugs on the fitting at 9 o’clock with the recesses in the aperture and inserting the fitting turn it clockwise to 12 o’clock. The ducting used must be 100mm (4") diameter and where flexible ducting is fitted it should not be turned through very tight bends as this could impair the performance of the cooker hood. The ducting used must be manufactured from fire retardent material produced to BS.476, DIN 4102-B1. (The maximum length of ducting including one 90° bend should be 3 metres, to be reduced by 1 metre for each 90° bend installed in the duct run). CHARCOAL FILTER - RECIRCULATION The cooker hood can be switched to recirculation (filtered) mode providing it is fitted with a charcoal filter. Charcoal filters can be obtained from your local Moffat Service Agent. To fit the charcoal filter open the grille as described above. Remove the aluminium knurled thumb screw from the centre of the fan cover. Place the charcoal filter over the fan cover and insert the knurled thumb screw through the hole in the centre of the filter into the captivated nut in the fan cover; turning the screw clockwise until the screw is finger tight. When installing the cooker hood ensure that the outlet on the top of the hood is free from obstructions to allow the purified air to pass from the hood back into the kitchen. The charcoal filter cannot be cleaned. It should be replaced at least once every three months or more frequently if the cooker hood is used for more than three hours a day. IMPORTANT: There could be a possible fire hazard if the charcoal filter is not replaced according to these instructions. USE AND CONTROLS The cooker hood functions are controlled by two slide switches located on the right hand side of the cooker hood and a conversion slider control inside the hood. Ensure the hood is wired in and the power supply is switched ON. The switch marked with the lamp symbol and numbered 0-1 controls the worktop illumination. Position -0 indicates the light is OFF. Position -1 indicates the light is ON. The switch marked with the fan symbol and numbered 1-2-3 controls the fan. Position -1 Should be selected when simmering or when using one pan. Position -2 Should be selected for normal cooking up to four pans. Position -3 Should be selected when frying or cooking food with strong odour. The slider control is located inside the hood behind the grille and converts the diffuser from ducting (extraction) to recirculation (filtered). NOTE: The hood is more effective when installed in the ducting mode (extraction). To obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking and leave it running for approximately 15 minutes after finishing. SYNTHETIC PAPER GREASE FILTER-EXTRACTION The grease filter is fitted to absorb grease and dust during cooking to help keep the appliance clean inside. The synthetic paper grease filter cannot be cleaned. It should be replaced at least every three months or more frequently if the hood is used for more than three hours a day. To replace the grease filter open the visor into the working position and remove the lower grille as described in the installation instructions. To remove the filter push the wire retaining clips to the side and remove. Clean the grille before fitting the replacement paper grease filter and refit the wire clips. IMPORTANT: There could be a possible fire hazard if the grease and charcoal filters are not replaced according to these instructions. MAINTENANCE AND CLEANING WARNING: DISCONNECT THE HOOD FROM THE MAINS SUPPLY BEFORE CARRYING OUT ANY KIND OF MAINTENANCE OR CLEANING WORKTOP LIGHTING If the lamp fails to function at any time first check that it is fully screwed into the holder. When changing the lamp an identical replacement must be fitted to ensure the safe working of the cooker hood. Replacement lamps are specified 240Volts 40Watt clear tubular, candle or, tulip shape with small Edison (E14) screw thread cap. For your own safety and i...
Otros modelos de este manual:Los aficionados - MH65B (311.91 kb)