Votos - 3, Puntuación media: 3.7 ( )

Fabricar: Dacor Tamaño del archivo: 434.68 kb Nombre del archivo: Idioma del manual:

the release lever B with the other. While pushing back on the release lever, lower the filter 2. out of the hood. On hoods with more than one filter, remove and clean all of the filters. To Clean the Filter(s): Hand wash the filter(s) in hot water with a mild detergent solution or dishwashing soap. Or you can place them in an automatic dishwasher. Dry the filter(s) completely before reinstalling. To Reinstall the Filter(s): Insert tabs on the end of the filter opposite the release 1. lever into the slots toward the back of the hood (above the hood rim). The release lever must be facing down. Push back on the release lever while sliding the free 2. end of the filter into the filter opening. Release the lever.3. Cleaning and Maintenance Maintenance Light Bulb Replacement Light bulb replacement is considered to be a homeowner maintenance operation. If all of the lights do not work, before replacing any bulbs, check to make sure power is on at the circuit breaker or fuse box. Replace the light bulbs only with Dacor Part No. 700975. Halogen Bulb Replacement Kit consist of a single bulb and suction cup, available from any authorized Dacor parts dealer. To replace the light bulb: Remove the right filter and turn off the main power 1. switch. Gently push the suction cup on the light replacement 2. tool A (provided with you range hood) onto the lens of the light bulb B . Turn the tool counter-clockwise until the bulb comes 3. loose. Remove the tool from the bulb and put it on the lens of 4. the replacement bulb. Screw the new bulb into the light fixture clockwise until 5. it is tight. Turn on power at the fuse or junction box. Turn on the main power switch and touch the light key to make sure it is working. Replace the filter.6. Replacement Parts DACOR PART # DESCRIPTION 700975 Halogen Bulb Replacement Kit 101617 Filter Product Specifications* Total Connect Load 120 Vac, 60 Hz, 9 Amps MAX (10 Amp MAX surge) Filters Mesh type, dishwasher safe Lights 120 Vac, 60 Hz, 75 W *Specifications subject to change without notice warning To prevent electric shock turn off power at the fuse or • junction box before replacing the light bulb. To avoid personal injury, make sure the cooktop or • range, the hood and the light are cool before changing the light bulb. 2 3 1 B A Before You Call For Service Problem Solution Guide PROBLEM MAY BE CAUSED BY WHAT TO DO Nothing Works. Control panel is not lit. Fan does not work. Power to hood is off. Turn on power at junction or fuse box. Check for tripped breaker or blown fuse. Power outage. Call electric company. Hood not connected to electric power. Have qualified electrician connect hood to electric power. Lights do not work. Control panel is not lit. See Nothing Works above. Light does not work. Control panel is lit. Loose light bulb. Check to make sure that the light bulb is screwed in completely (see page 6). Light bulb burned out. Replace light bulb (see page 6). Fan does not draw heat and smoke properly. Fan set to low setting. See Operating Instructions section. Filter(s) clogged or dirty. Check filters. Make sure they are completely clean and not blocked by foreign objects. Damper jammed shut or duct work clogged. Consult with a qualified installation professional.* Fan shuts off by itself. Timed feature used. If the timer is set, the fan will turn off after ten minutes. See Timed Feature on page 4. Fan does not work. Control panel not lit. See Nothing Works above. Fan does not work. Control panel lit. Fan malfunction. Call for service. Fan comes on by itself. Hood AUTO-ON feature. The fan comes on automatically when the temperature rises above 140°F (60°C). The AUTO-ON feature protects the control panel from damage due to overheating. The fan will automatically turn off when the temperature goes below 140°F (60°C), if the fan control is set to “off”. This safety feature cannot be turned off. See page 4 for more details. * The duct work connected from the range hood chimney to outside the house or building required to vent heat and smoke is not manufactured, warranted or serviced by Dacor. The customer is responsible for having a qualified installer install and maintain the duct work. Warranty & Service Product Maintenance Do not perform any maintenance other than that instructed in the Cleaning and Maintenance section of this manual. A qualified service technician should perform all other service. Getting Help Before you obtain service, please review the Before You Call for Service section of this manual starting on page 7. If you have performed the checks in the Problem Solution Guide and the problem has not yet been remedied, please visit our web site or contact our Customer Service Team for a listing of Dacor authorized service agents. Prior to requesting service, it is helpful to be familiar with the warranty terms and conditions on this page. Contact us through our web site at: Dacor Customer Service Team: Tel: (800) 793-0093 Fax: (626) 403-3130 Business Hours: ...

Descargar ahora

Introduzca dos números de la imagen: