Votos - 3, Puntuación media: 4 ( )

Fabricar: Emerson Tamaño del archivo: 205.17 kb Nombre del archivo: Idioma del manual:

Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball. A loose setscrew could create fan wobble. WARNING ! It is critical that the pin in the hanger ball is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling. 9. The fan comes with blue, black and white leads that are 80” long. Before installing fan, measure up approximately 6 to 9-inches above the ball/ downrod assembly. Cut off excess leads and strip back insulation 1/2-inch from end of leads. Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds. WARNING ! To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked acceptable for fan support, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture. WARNING ! Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with national and local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock. How to Hang Your Ceiling Fan Figure 6 AT LEAST 7' CEILING FLOOR WARNING ! The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. 1. Securely attach the hanger bracket to the outlet box using the two screws supplied with the outlet box. (Figure 7). WARNING ! Hanger bracket must seat firmly against outlet box. If the outlet box is recessed, remove wall board until bracket contacts box. If bracket and/or outlet box are not securely attached, the fan could wobble or fall. OUTLET BOX TWO SCREWS SUPPLIED WITH TAB OUTLET BOX HANGER BRACKET Figure 7 2. Carefully lift the fan and seat the hanger ball/ downrod assembly on the hanger bracket that was just attached to the outlet box (Figure 8). Be sure the groove in the ball is lined up with tab on the hanger bracket (Figure 7). WARNING ! Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard. NOTE: CEILING COVER, SUPPLY WIRES AND OUTLET FAN WIRES OMITTED BOX FOR CLARITY. HANGER BRACKET Figure 8 DOWNROD ASSEMBLY HANGER BALL/ WARNING ! WARNING ! The fan must be hung with at least 7' of clearance To avoid possible fire or shock, do not pinch wiresfrom floor to blades (Figure 6). between the hanger ball/downrod assembly and the NOTE: For ease of installation, first the fan motor hanger bracket. and housing assembly is installed on the ceiling. Then after wiring of the fan is completed, the fan blade assemblies will be attached to the motor hub. 5 How to Wire Your Ceiling Fan If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. WARNING ! To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. NOTE: If you are not sure if the outlet box is ground- ed, contact a licensed electrician for advice, as it must be grounded for safe operation. 1. Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the grounding conductor of supply (this may be a bare wire or wire with green colored insulation) (Figure 9). Securely connect wires with wire connector supplied. NOTE: CEILING COVER OMITTED FOR CLARITY. LISTED WIRE CONNECTOR (3) GREEN WIRE (GROUND) FROMHANGER BRACKET GREEN WIRE (GROUND) FROMHANGER BALL WHITE SUPPLY (NEUTRAL) WHITE FAN WIRE BLACK SUPPLY (HOT) BLACK AND BLUE FAN WIRES Figure 9 SUPPLY GROUND WIRE NOTE: If you are using an Emerson Light Fixture with your fan, see Light Fixture Ow...

Descargar ahora

Introduzca dos números de la imagen: