Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Bulk fuel storage shall be outside the struc- ture. f) All fuel storage shall be located a minimum of 25 feet from heaters, torches, welding equipment, and similar sources of ignition (exception: the fuel reservoir integral with the heater unit). g) Whenever possible, fuel storage shall be confined to areas where floor penetra- tions do not permit fuel to drip onto or be ignited by a fire at lower elevation. h) Fuel storage shall be in accordance with the federal, state, or local authority hav- ing jurisdiction. • Never use heater where gasoline, paint thinner, or other highly flammable vapors are present. • Follow all local ordinances and codes when using heater. • Heaters used in the vicinity of tarpaulins, canvas, or similar enclosure materials shall be located a safe distance from such materials. The recommended mini- mum safe distance is 10 feet. It is further recommended that these enclosure materials be of a fire retardant nature. These enclosure materials shall be se- curely fastened to prevent them from igniting or from upsetting the heater due to wind action. • Use only in well-vented areas. Before using heater, provide at least a three-square- foot opening of fresh, outside air for each 100,000 BTU/Hr of rating. This heater produces carbon monoxide, which is listed by the State of California as a reproductive toxin under Proposition 65. • Use only in places free of flammable vapors or high dust content. • Use only the electrical voltage and frequency specified on model plate. • Use only a three-prong, grounded extension cord. • Minimum heater clearances from combustibles: Outlet: 8 Ft. Sides: 4 Ft. Top: 4 Ft. Rear: 4 Ft. • Locate heater on a stable and level surface if heater is hot or running or a fire may occur. • When moving or storing heater, keep heater in a level position or fuel spillage may occur. • Keep children and animals away from heater. • Unplug heater when not in use. • When used with thermostat, heater may start anytime. • Never use heater in living or sleeping areas. • Never block air inlet (rear) or air outlet (front) of heater. • Never move, handle, refuel, or service a hot, operating, or plugged-in heater. • Never attach duct work to front or rear of heater. PRODUCT IDENTIFICATION Hot Air Outlet Fan GuardLower Shell Air Filter End CoverFuel Tank Fuel Cap Side Cover Handle Power Cord Upper Shell Flame-Out Control Reset Button Figure 1 - 35/50/55/70,000 BTU/Hr Models Hot Air Outlet Lower Shell Side Cover Fuel Tank Fuel Cap Fan Guard Power CordFlame-Out Control Reset Upper Shell Button Figure 2 - 100/110/150,000 BTU/Hr Models 4 UNPACKING ASSEMBLY (For 100,000, 110,000, and 150,000 BTU/Hr Models Only) 1. Remove all packing items applied to heater for shipment. 2. Remove all items from carton. 3. Check items for shipping damage. If heater is damaged, promptly inform dealer where you bought heater. These models are furnished with wheels and a front handle. Some models are furnished with a rear handle also. Wheels, handle(s), and the mounting hardware are found in the shipping carton. Tools Needed • Medium Phillips Screwdriver • 3/8" Open or Adjustable Wrench • Hammer 1. Slide axle through wheel support frame. Install wheels on axle. IMPORTANT:When installing wheels, point extended hub of wheels toward wheel support frame (see Figure 3). 2. Place cap nuts on axle ends. Gently tap with hammer to secure. 3. Place heater on whee...
Otros modelos de este manual:Los aficionados - 100 (277.27 kb)
Los aficionados - 000 (277.27 kb)
Los aficionados - 000 50 (277.27 kb)
Los aficionados - 000 55 (277.27 kb)