Votos - 3, Puntuación media: 3
(
)
)
|
Resumen del manual
Return appliance to manufacturer for examination, electrical or mechanical adjustment, or repair. 9. DO NOT operate in the presence of explosive and/or flammable fumes. 10.Use appliance only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by Bionaire® may cause hazards. 11.DO NOT use outdoors. 12.Always use on a dry, level surface. 13.Keep unit away from heated surfaces and open flames. 14.DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only. Step 2: If the fan does not fit snugly to the top and bottom of the window casing, attach the included extender panel(s) and pull out the built-in extender screen until the fan fits safely in your window (See Figure 3). Step 3: To keep the fan in place, carefully close the window so that the bottom edge of the window rests on the flat area on the top of the window fan. WARNING: Be sure fan is securely installed in your window at all times. Do not lean or push on fan while it is in the window. NOTE: For slider windows, set the fan vertically in your window opening, with the left side on the bottom. INSTALLATION GUIDE Figure 3 FRONT VIEW LEFT RIGHT Built-In, Pull Out Extender Screen Extra Extender Panels 24 inch (61cm) long PULLS OUT UP TO 7.0 inch (17.8cm) The extender panels can be secured to the fan by simply sliding the extender panels into the grooves located on the left hand side of the fan. The extender screen can be adjusted by pulling out the extender locks located on the top and bottom of the right side of the fan. Push the locks back into place to secure the extender screen at the desired length. For 24 inch to 27 inch (61-69cm): Use up to 3 inch (7cm) of right side, pull out extender screen. For 28 inch to 34 inch (71-86cm): Use one 3 inch (7cm) extender panel on the left side. Adjust the pull out extender screen on the right side for a tight fit (from 0.5 inch to 7 inch (1.3-17.8cm) ). For 35 inch to 37 inch (89-94cm): Use two 3 inch (7cm) extender panels on the left side. Adjust the pull out extender screen on the right side for a tight fit (from 0.5 inch to 7 inch (1.3-17.8cm) ). Larger than 37 inch (94cm): Additional extender panels will be required. MANUAL OPERATING INSTRUCTIONS NOTE: To operate the fan continuously, make sure that the auto on light located to the left of the control panel is off. Step 1: Plug your window fan into any 120V AC electrical outlet. NOTE: The temperature display will always be on when the fan is plugged into the electrical outlet. Two 3.0 inch (7cm) extenders, (Included in your box packed at both ends) Step 2: To turn the fan on press the Speed Control Button. Step 3: Set the speed to high, medium (med) or low by pressing the Speed Control Button. Step 4: Set the airflow direction to Exhaust (out), Intake (in) or exchange (one blade blowing air in and the second blade blowing air out) by pressing the air flow button. Step 5: To turn the fan off press the Speed Control Button until the fan stops. AUTOMATIC OPERATING INSTRUCTIONS Your window fan is equipped with the digital control thermostat that automatically turns the fan on and off depending upon the preset comfort level. For example, if you have set your thermostat to 75 degrees and the room temperature drops to 74 degrees or lower then the fan will automatically shut off. The fan will then turn on again when the room temperature exceeds 75 degrees. In order to take advantage of this feature, make sure your window fan is in automatic mode (this will be indicated by a red light on the left of the control panel). Step 1: Set the fan to Automatic Mode by pressing the Mode button located on the Control Panel. The Auto On light will illuminate when the unit is in Automatic Mode. Step 2: Press the Temp Set (+,–) buttons on the front of the Control Panel or use the remote control to program the desired temperature or switch to the manual mode. Step 3: When you are finished setting the temperature, let go of the button. The display will blink a few times and then will return to displaying the current room temperature. IMPORTANT: If the unit will not start in automatic mode, please make sure that the set temperature is below the current room temperature. If the fan is stopped and you would like to turn it back on, lower the set temperature or switch to the manual mode. REMOTE CONTROL INSTRUCTIONS Your window fan is equipped with a remote control. This remote control can be used to adjust the following functions: Power, Manual/Automatic mode, Air Flow Direction, Temperature adjustments. Two “AAA” batteries have been included for your convenience. • Do not mix old and new batteries. • Do not mix alkaline, standard (carbon-zinc),or rechargeab...