Votos - , Puntuación media:
(
)
)
Fabricar: Bionaire
Tamaño del archivo: 554.03 kb
Nombre del archivo: 5b443770-fd9d-6814-3d3c-ccd5d165c944.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
AND IRELAND The wires in this mains lead are coloured in accordance with the following code: Blue -Neutral Brown -Live This appliance is fitted with a 13 amp plug. The fuse should be rated at 3 amps and ASTA approved to BS1362. However if the plug is unsuitable, it should be removed from the supply cord and an appropriate plug fitted as detailed below:As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black. The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red. NB. Neither wire should be connected to the terminal in your plug which is marked with the letter E or by the Earth symbol or Green and Yellow. If in doubt consult a qualified electrician. If any other plug is used, a 3 amp fuse must be fitted either in the plug or adaptor or at the distribution board. NOTE: If the terminals in the plug are not marked or if you are unsure or in doubt about the installation of the plug please contact a qualified electrician. If a 13A 3-pin plug is fitted, it must be an ASTA approved plug, conforming to BS1363 standard. Replacement 3A fuses must be BSI or ASTA BS1362 approved. GUARANTEE PLEASE KEEP YOUR RECEIPT AS THIS WILL BE REQUIRED FOR ANY CLAIMS UNDER THIS GUARANTEE. • This product is guaranteed for 3 years. • In the unlikely event of breakdown, please take it back to the place of purchase, with your till receipt and a copy of this guarantee. • The rights and benefits under this guarantee are additional to your statutory rights which are not affected by this guarantee. • Holmes Products Europe undertakes within the specific period, to repair or replace free of charge, any part of the appliance found to be defective provided that: • We are promptly informed of the defect • The appliance has not been altered in any way or subjected to misuse or repair by a person other than a person authorised by Holmes Products Europe. • No rights are given under this guarantee to a person acquiring the appliance second hand or for commercial or communal uses. • Any repaired or replaced appliance will be guaranteed on these terms for the remaining portion of the guarantee. The Bionaire® Group reserves the right to change or modify any specifications without notice. THIS PRODUCT IS MANUFACTURED TO COMPLY WITH THE E.E.C. DIRECTIVES 73/23/EEC, 89/336/EEC and 98/37/EEC. Holmes Products (Europe) Ltd 1 Francis Grove London SW19 4DT England Fax: +44 (0)20 8947 8272 Email: info-europe@theholmesgroup.com Website address: UK - Free phone Customer Service Helpline – 0800 052 3615 2 Cool™ Stand Fan BASF1016 INSTRUCTION MANUAL 9100010004526 BASF1016IUK04EM1 BASF1016IUK04EM1 V.qxd 1/20/05 09:40 Page 4 U.K. and IRELAND pole clockwise to lock in position. Be careful to align the cutaway grooves on the threaded joint grooves on the neck joint with the two protruding raised pieces inside the hollow end of the pole. 2. Lastly, insert the tilt adjustment knob (N) into the neck joint and tighten until it is securely in place. OPERATING INSTRUCTIONS 1. Set the fan base on a dry level surface. 2. Make sure the Selector (Speed) Control is in the OFF(0) position. Selector (Speed) Control is located on the top of the fan motor housing. 3. Plug the cord into a suitable 220-240V. AC outlet. 4. The SPEED is adjusted by turning the Selector (Speed) Control to the desired setting: 0 - Off I - Low II - Med III - High 5. The OSCILLATION control (L) is located on the top of the fan motor housing. To start oscillation, push the control knob down.To stop oscillation, pull the control knob up. ADJUSTMENT Tilt adjustment 1. To change the tilting angle of the fan head, simply loosen the tilt adjustment knob (N). 2. Move the fan head to the desired angle, then firmly tighten the knob to lock in place. Height adjustment This fan is equipped with two poles which allow you to adjust the height of the fan for two height settings. With one pole only, the fan can be used on a table or floor. With both poles fitted it is a floor standing fan. • Small pole 760mm (30") • Longer pole 910mm (36") • Both poles 1250mm (50") Floor to table conversion 1. Remove the fan head by turning it anti-clockwise and lifting off the pole. Remove one of the poles, (see above for heights available). 2. Refit the fan head as detailed in "Final assembly". CLEANING AND MAINTENANCE Follow these instructions to correctly and safely care for your Bionaire® fan. Please remember: • Always unplug the fan before cleaning or assembly. • Do not allow water to drip on or into the fan motor housing. • Be sure to use a soft cloth, moistened with a mild soap solution. • Do not use any of the following as a cleaner: petrol, thinners or benzine. Fan Blade ...