Votos - , Puntuación media:
(
)
)
Fabricar: Miele
Tamaño del archivo: 1.04 mb
Nombre del archivo: DA390-5_us.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
. Press the On/Off button to turn the fan off . The . indicator goes out. Overhead lighting . The overhead lighting can be turned on and off independently of the fan. . Press the light button . briefly to turn on the lighting. Automatic Safety Shut-Off The fan will turn automatically off 10 hours of use. The lighting however will remain on. . Press the On/Off button . to turn the fan back on again. Cleaning and Care WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before cleaning or servicing the hood, disconnect it from the power supply, see "Important Safety Instructions". The halogen bulbs are very hot when in use. They stay hot for some time after turned off. Use caution, danger of burns. Wet cleaning the hot bulbs will cause damage. Wait a few minutes after turning them off before cleaning. Cleaning the casing Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the hood. They will damage the surface. . All external surfaces and controls can be cleaned with a mild solution of warm water and liquid dish soap applied with a soft sponge. Do not use too much water when cleaning the controls. Water could penetrate the electronics and cause damage. . Wipe dry using a soft cloth. Avoid: – cleaning agents containing soda, acids or chlorides, – abrasive cleaning agents e.g. powder or cream cleansers, – abrasive sponges, e.g. pot scourers or sponges which have been previously used with abrasive cleaning agents. These will damage the surface. The following instructions for cleaning "Stainless steel" surfaces and "Stainless steel colored controls" should be followed in addition to the general "Cleaning the casing" instructions. Special instructions for stainless steel surfaces (not applicable to the controls) Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner. To help prevent resoiling, a conditioner for stainless steel can be applied. Special instructions for colored casings (RAL) (Special order) It is very difficult to clean this type of surface without causing minor marks to the surface material. This can become particularly noticeable with darker colors and if there is halogen lighting in the kitchen. Stainless steel colored controls These controls may become discolored or damaged if not cleaned regularly. Do not use a stainless steel cleaner on these controls. Grease filters The reusable metal grease filters in the hood remove solid particles from the vented kitchen air (grease, dust, etc) and prevent soiling of the ventilation system. The grease filters should be cleaned every 3 - 4 weeks. A dirty filter is a fire hazard. To remove the grease filter pull the locking clips forward 1., lower the filter down 45° 2., unhook it at the rear 3., and take it out. Support the grease filter so that it does not fall and damage the cooktop. Cleaning the grease filter By hand: use a scrub brush with a solution of warm water and mild detergent. Do not use the pure detergent, aggressive all purpose cleaners, oven sprays, abrasive cleaning agents or limescale removers. They could destroy the filter. In a dishwasher: place the filter vertically in the lower basket, making sure that the spray arm is not blocked. Use a wash program with a max. temperature of 150°F (65°C). In a Miele dishwasher use the "Normal" program. Use the recommended amount of dishwasher detergent. Overuse could destroy the filter. Depending on the detergent, cleaning the grease filter in a dishwasher may cause permanent discoloration of the filter surface. Performance of the filter will not be affected by this discoloration. After cleaning, the filter can be placed on a towel to air dry. While the filters are removed, clean any dirt or grease from the filter casing. Cleaning and Care 13 Cleaning and Care . When putting the grease filters back make sure that the locking clips are visibly facing the cooking surface Active charcoal filter In recirculation mode an active charcoal filter must be used in addition to the grease filters. It is designed to absorb cooking odors. The active charcoal filter will be replaced in the canopy above the grease filters. Replacement active charcoal filters can be ordered from Miele. . To install or replace the charcoal . If the filters are incorrectly installed, filter, the grease filters must first be insert a small screwdriver into the slit removed as described in the along its edge to disengage it from previous section. the casing. . Remove the charcoal filter from the packaging. . Insert the charcoal filter into the canopy. . Replace the grease filters. Replace the active charcoal filter at least every 6 months or when they no longer absorb odors efficiently. Used charcoal filters may be discarded in household trash. Cleaning and Care Changing the light bulbs WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before changing the light bulbs, disconnect the h...