Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
AEG — putting words into action. 3 4 General The cooker hood can be used : either as an exhaust air appliance (extraction mode) or as a return air appliance (recirculation mode) - filtering through an active carbon filter (optional extra). Notes prior to installation in the extraction mode the exhaust air must not be introduced into a smoke flue or exhaust gas chimney. Introduction of the exhaust air into a shaft used for ventilation of the installation spaces of firerooms is not permitted. If the exhaust air is introduced into a operational smoke flue or exhaust gas chimney, it is advisable to seek the advice of a competent chimney-sweep. The official exhaust air guidance regulations are to be complied with. During operation in the extraction mode, an adequate air opening of approximately the same size as the exhaust air opening should be ensured. According to the Provincial Building Regulations, the joint operation of fume extractor hoods and chimneylinked fireplaces, such as coal or oil-fired ovens and gas heaters, in the same space is subject to specific restrictions. In such spaces, the Fireplace Regulations only allow an underpressure of max. 0.04 mbar. The safe joint operation of chimneylinked appliances and fume extractor hoods is only guaranteed if space and/or dwelling (space/air interaction) are externally vented by a suitable supply air opening of around 500-600cm2 and an underpressure thereby avoided when the cooker hood is running. In doubtful cases, please seek the advice and consent of a competent chimney-sweep or the local building authorities. In spaces without a fireplace, the rule is: “Supply an air opening as large as the exhaust air opening”, the efficiency of the hood in the extraction mode may be impaired by a greater opening. Operation of the hood in the recirculation mode in such circumstances is safe and is not subject to the regulations above. When installed, the minimum distance from the hob to the lower edge of the cooker hood must be 60cm for electric hobs or 70cm in the case of gas or mixed fuel hobs. Important: 5 Electrical connections Voltage and current Important Please ensure that the voltage and current indicated on the rating plate agree with the voltage of your electricity supply. If your appliance has been equipped with a mains lead with a moulded-on type plug, you must comply with the following regulations: The plug moulded on to the lead incorporates a fuse. For replacement, use a 5 amp BS1362 fuse. Only ASTA approved or certified fuses should be used. If the fuse cover/carrier is lost, a replacement cover/carried must be obtained from an electrical goods retailer. If the socket outlets in your home are not suitable for the plug fitted to the appliance, then the plug must be cut off and destroyed for safety reasons, and an appropriate plug fitted. When wiring the plug ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead clamp on the plug. Electrical connections 230 V - using fixed power supply line with plug. 240 V - using fixed power supply line (Great Britain). Fuse rating 13 amps (The unit should only be connected up by an authorized electrician). See rating plate for further information. It is recommended that the socket for the plug is sited above the cooker hood or above the overhead cabinet. This has 2 advantages: 1) The socket is not visible. 2) The appliance can easily be unplugged when necessary. If a fixed connection is required the cooker hood should be connected by an electrical installer registered with a competent electricity company. An isolating device is to be provided on the fixed wiring side. Switches with a contact opening of more than 3mm apply as isolating devices. These include-automatic cut-out switches, fuses and contactors (VDE 0730, s. 7, Parti). 6 Your appliance must be connected to fixed wiring via the use of a double pole swiched fused spur outlet with or without pilot lamp. We strongly recommend the appliance is connected by a qualified electrician who is a member of the NICEIC who will comply with the I EE and any local regulations. NOTE: The terminology “DOUBLE POLE” means that both the live and neutral supplies are swiched and disconnected at the same time. The terminations labelled SUPPLY are for the connection for the internal house wiring and the terminations labelled LOAD are for the appliance. IMPORTANT The wires of the mains lead supplied with this appliance are coloured in accordance with the following code: Blue-Neutral Brown-Live As the colours of the flexible cord of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The whire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. ...