Votos - 3, Puntuación media: 3
(
)
)
|
Resumen del manual
NOTE: The terminology “DOUBLE POLE” means that both the live and neutral supplies are swiched and disconnected at the same time. The terminations labelled SUPPLY are for the connection for the internal house wiring and the terminations labelled LOAD are for the appliance. IMPORTANT The wires of the mains lead supplied with this appliance are coloured in accordance with the following code: Blue-Neutral Brown-Live As the colours of the flexible cord of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:The whire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. N LOAD L SUPPLY L LOAD N SUPPLY DP 13A, 250V BLUE (NEUTRAL) BROWN (LIVE) FUSE ON Appliances with 3 wires Your appliance must be connected to fixed wiring via the use of a double pole swiched fused spur outlet with or without pilot lamp. We strongly recommend the appliance is connected by a qualified electrician who is a member of the NICEIC who will comply with the IEE and any local regulations. NOTE: The terminology “DOUBLE POLE” means that both the live and neutral supplies are swiched and disconnected at the same time. The terminations labelled SUPPLY are for the connection for the internal house wiring and the terminations labelled LOAD are for the appliance. WARNING:THIS APPLIANCE MUST BE EARTHED IMPORTANT The wires in this mains lead are coloured in accordance with the following code: Green/Yellow - Earth Blue - Neutral Brown - Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminate in your spur box, proceed as follows: The wire which is coloured green and yellow must be connected to the terminal which is marked with the letter “E” or by the earth symbol or coloured green or green and yellow.The wire which is coloured blue must be connected to the terminal which is marked with the letter “N” or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter “L” or coloured red. BLUE BROWN (NEUTRAL) (LIVE) FUSE ON GREEN & YELLOW (EARTH) N LOAD L SUPPLY L LOAD N SUPPLY DP 13A, 250V Specifications Dimensions: Height Width Depth (in mm) 152 599 505 Weight: Net: 8.7 Kg Gross: 9.6 Kg Length of the cable: 140 cm Maximum absorbed power: 230 W Motor absorption: 1 x 150 W Lighting: 2 x 40 W Fan powers (levels), levels in compliance with DIN 44971 Level: Min. Max. Intensive Extractor: 116 m3/h 175 m3/h 265 m3/h Filter: 60 m3/h 14 5 m3/h 175 m3/h Extractor system: 100 and 120 mm O Safety warnings for kitchen unit installer Installation When used as an extractor unit, the hood must be fitted with a 100 or 120 mm diameter hose. If the outlet hose is installed in a horizontal position, it must be slanted at an angle of 10° so that the air can flow outside without impediment. When installing the hood, make sure you respect the following minimum distance from the top edge of the cooking hob/ ring surfaces: electric cookers 650 mm gas cookers 650 mm coal and oil cookers 700 mm min. The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must under no circumstances be connected to ventilation ducts for rooms in which fuel-burning appliances are installed. It is advisable to apply for authorization from the relevant controlling authority when connecting the outlet to an unused chimney flue or combustion gas duct. The air outlet installation must comply with the regulations laid down by the relevant authorities. When the unit is used in its extractor version, a sufficiently large ventilation hole must be provided, with dimensions that are approximately the same as the outlet hole. National and regional building regulations impose a number of restrictions on using hoods and fuel-burning appliances connected to a chimney, such as coal or oil room-heaters and gas fires, in the same room. Hoods can only be used safely with appliances connected to a chimney if the room and/or flat (air/environment combination) is ventilated from outside using a suitable ventilation hole approximately 500-600 cm2 large to avoid the possibility of a depression being created during operation of the hood. If you have any doubts, contact the relevant controlling authority or building inspector’s office. Where flexible ducting is fitted the length should be no more than: — 3 metres with one 90° bend — 2 metres with two 90° bends. Bends of more than 90° will reduce the efficiency of the hood and reduce the air flow. Since the rule for rooms with fuel burning appliances is “outlet hole of the same size as the ventilation hole”, a hole of 500-600 cm2, which is to say a larger hole, could reduce the performance of the extractor hood. If the hood is used in its recirculating mode, it wi...