Votos - , Puntuación media:
(
)
)
Fabricar: Electrolux
Tamaño del archivo: 209.2 kb
Nombre del archivo: 533cad26-a0cd-bc14-3570-6a3a2710444c.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
Bends of more than 90° will reduce the efficiency of the hood and reduce the air flow. General details The hood is supplied as a ducted version, but may also be used in recirculation mode by inserting a charcoal filter (Special accessories). The air is ducted out through a pipe which is connected to the outlet hole A (fig. 1) by means of a coupling flange B. To connect the hood to a wall box, you use hoses and wall boxes as offered on the AEG price list as optional extras. B A Extractor version 1 7 8 Cooking vapours are cleaned by the charcoal filter (Special accessories) and ducted back into the kitchen. The AEG original KF-Plus charcoal filter is necessary for the recirculating mode (see paragraph “Special accessories”). For the recirculating mode proceed as follows: a) Remove the grid by turning knob A (fig. 2). b) Position the filter (fig. 3) and rotate clockwise until it stops. In this mode air will be expelled through an exhaust pipe with an internal diameter of 100 mm on the top of the cupboard. c) Replace the grid. 2 A A 3 Filter version Description of the appliance 1) Light switch 2) Motor switch 3) Work surface lamp 4) Grid 4 3 2 1 Technical details Model 502 D Net weight: 5 kg Height 145 mm Width 520 mm Depth 285 mm Absorbed power: 160W Motor: 1 x 120 W Lighting: 1 x 40 Watt Lengt of the cable: 110 cm Fan powers (speed), speed in compliance with DIN 44971 Speed: 123 Extractor version: 126 m3/h 149 m3/h 185 m3/h Filter version: 110 m3/h 133 m3/h 170 m3/h Flange: 100 mm O Fixing the hood After having adjusted the hood for the version required, it may be installed. This appliance is designed for fitting in a cabinet or some other support. The opening to be made on the bottom of the wall-hung cabinet must correspond with the measurements shown in fig. 4 (495 X 260 mm). To fix the hood proceed as follows: a) remove the grid. b) Fit the hood into the opening. c) Secure the unit to the cabinet by screwing up screws through holes C (fig. 4). d) Replace the grid. 4 C C 10 The hood is fitted with one variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 5-15 minutes after having finished, thus ensuring that all that cooking odours are eliminated. Never leave a cooking hob or ring on without a pot or pan on top of it, to avoid the possibility of excess heat damaging the unit. Gas, oil or coal cooker flames in particular should never be left uncovered. Special care should be taken when using deep fat fryers since the oil in them can overheat and burst into flames. The risk of fat catching fire is increased when using dirty oil. It is extremely important to note that overheating can cause a fire. Never carry out any flambe cooking under the hood. Always disconnect the unit from the power supply before carrying out any work on the hood, including replacing the light bulb (take the cartridge fuse out of the fuse holder or switch off the automatic circuit breaker). It is very important to clean the hood and the grease filters at the recommended intervals. Failure to do so could cause grease deposits to build up, causing a fire hazard. Safety warnings for user 11 Controls Hood Operation The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated. The control switches are located on the unit’s front panel: the light switch (A) switches the hood lamp on and off; the motor switch (B) switches the cooking smoke and vapour extractor motor on and off, enabling you to select one of the three different speeds. B A 12 Care and Maintenance Before performing any maintenance operation, disconnect the hood from the electricity. The hood has a metal grease filter. To clean the filter, proceed as follows: Open the grill by turning knob A (fig. 2). Metal grease filter 2 AA Pull the two plastic stops B as shown by the arrows (fig. 5) and remove the metal filter. 5 BB You should take out the metal filter every four weeks and wash it either in the dishwashing machine or by hand. Clean the internal housing only with warm washing-up water — do not use any harsh cleaners, brushes, or abrasive. Soak metal filter cassette for about one hour in hot water with a greaseHand- washing loosening cleaner, then rinse off thoroughly with hot water. Repeat the process if necessary. Re-fit the cassette when it is dry. Place metal filter cassette in dishwasher. Select most powerful Dishwashing washing program and highest temperature, at least 65° C. Repeat the machine process. Re-fit the cassette when it is dry. When washing the metal grease filter in the dishwasher a slight discoloration of the filter can occur. 13 Charcoal filter The charcoal filter must be changed at least every 4 months. The charcoal filter cannot be washed ...