Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Technical Information DIMENSIONS HEIGHT OF CANOPY: 24cm HEIGHT OF CHIMNEY: (UPPER SECTION) 40cm (LOWER SECTION) 36cm WIDTH OF CANOPY: 120cm DEPTH OF CANOPY: 49cm GROSS: 20kg NET: 16,8kg ELECTRICAL SUPPLY: VOLTAGE: (50Hz) 220-240 V POWER CONSUMPTION: 225W FAN MOTOR: 145W LIGHT BULB: (2 x 40 W) 80W SUITABLE FOR INSTALLATION ABOVE: ELECTRIC HOB: 7KW (max) GAS HOB: 10KW (max) SLOT-IN GAS COOKER 13.5KW (max) SLOT-IN ELECTRIC COOKER 12.4KW (max) Note: CE Marking certifies that this appliance complies with the requirements laid down in EEC directive 89:336. (Electromagnetic compatibility) and subsequent modifications and Low Voltage directive 72/23/E. ELECTRICAL CONNECTIONS This appliance must be earthed Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood. This appliance is fitted with a 3 core mains cable and must be permanently connected to the electricity supply via a double-pole switch having 3mm minimum contact gap on each pole. A Switched Fuse Connection Unit to BS1363 Part 4, fitted with a 3 Amp fuse, is a recommended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions. This appliance conforms to BS 800: 1988 and EEC Directive No. 78 308 regarding suppression of radio and television interference. 10 INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood. Installation Requirements Before installation check the wall to which the cooker hood is to be fitted for electric cables, water pipes or gas. This cooker hood is designed to be fixed to any vertical surface over a cooking area, and can be used in the extraction (ducted to the outside) or recirculation mode. The installation work must be undertaken by a qualified and competent person. The manufacturer disclaims any responsibility for damage due to incorrect installation of the cooker hood or if the hood is not installed in compliance with relevant regulations controlling this type of installation. Unpacking The cooker hood is supplied with the following components for installation: • Canopy (C), including controls, worktop illumination and fan unit. • U-shaped upper chimney section (S). • U-shaped lower chimney section (I). • Metal recirculation plate (T). • 120mm ducting spigot (A). Fixing kit comprising: • Wall fixing brackets (1,2 and 3). • Document pack. 11 Clearance Height The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, providing the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications. If the output of the appliance below the cooker hood exceeds the maximum outputs quoted, please refer to the cooker manufacturer’s installation instructions. A minimum clearance height of 650mm (25 1/2 ”) is required when installed above a built-in electric hob, or 700mm (27 1/2 ”) when installed above a built-in gas hob. A minimum clearance height of 685mm (27”) is required when installed above a slot-in electric cooker, or 787mm (30 1/2 ”) when installed above a slot-in gas cooker. When installed between adjoining wall cabinets, the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and the worktop must be 450mm. If the height of the wall cabinet is less than 450mm, a gap of 50mm must be maintained either side of the hob. This cooker hood must not be installed above a cooking appliance with a high level grill. Fitting the Wall Brackets 1. Draw a vertical line on the wall from the centre of the cooking appliance up to the ceiling, using a spirit level and marking pen. This is to ensure the correct vertical alignment of the appliance. 2. Draw a horizontal line through the vertical at 270mm. Mark the centre positions for the lower bracket fixing screws (1) at 110mm either side of the vertical line (screws not supplied). Ensure that the distance between the lowest point of the hood and the cooking appliance beneath meet the clearance requirements quoted above. 3. Draw a horizontal line through the vertical at 45mm from the ceiling or from the maximum height of the chimney. Mark the centre positions for the upper bracket fixing screws (2) at 80mm either of the vertical line (screws not supplied). Hob A: Built-in Electric Hob...