Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
This chimney hood is designed to be fixed to any vertical surface over a cooking area, and can be used in the extraction (ducted to the outside) or recirculation mode. The installation work must be undertaken by a qualified and competent person. RANGEMASTER Consumer Products disclaims any responsibility for damage due to incorrect installation of the chimney hood or if the hood is not installed in compliance with relevant regulations controlling this type of installation. 10 (Square) (Square) (Square) D INSTALLING THE CHIMNEY HOOD CLEARANCE HEIGHTS The chimney hood is designed to be fitted over a cooking appliance. A minimum clearance height of 650mm (25.ins) is required when installed above a built-in electric hob, or 700mm (27.ins) when installed above a built-in gas hob. When installed between adjoining wall cabinets, the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and worktop must be 450mm (17.ins), and a gap of 50mm (2ins) must be maintained either side of the hob. This chimney hood must not be installed above a cooking appliance with a high level grill. FITTING THE WALL BRACKETS 1. Draw a vertical line on the wall as illustrated, from the centre of the cooking appliance up to the ceiling using a spirit level and marker pen. This is to ensure the correct vertical alignment of the various components during installation. 2. Place one of the brackets (2) against the wall, centrally over the vertical line approximately 2mm from the ceiling or from the upper most fixing point. Align the bracket using a spirit level and mark the two keyhole centre positions for the upper bracket fixing screws on the wall. 3. Place the second bracket (2) against the wall, centrally over the vertical line at distance X. (X being determined by the measurement of the upper chimney). Align the bracket using a spirit level and mark the two keyhole centre positions for the middle bracket fixing screws on the wall. 45 11 INSTALLING THE CHIMNEY HOOD 4. Drill the holes for the fixing screws 5. When the electrical connection has using an 8mm masonry drill bit. Insert the rawl plugs and fix the brackets (2) using the 4.2 x 44.4mm screws provided. DRILLING THE HOLES 1 1. Draw a horizontal line through the vertical 970mm up the wall from the top of the cooking appliance, ensuring it is level with a spirit level. 2. Mark the centres for the holes 1, 116mm either side of the vertical line. 3. Drill the two holes 1 for the fixing screws using an 8mm masonry drill bit. Insert the rawl plugs and the 4.2 x 44.4mm screws provided. Tighten the screws, leaving a space of 5-6mm between the head and the wall. Note: If the chimney hood is to be installed onto a hollow construction plaster or partition board wall then special fixing screws will be required (not supplied). FIXING THE CANOPY 1. Before starting to fix the canopy to the wall, it is necessary to adjust the support brackets S1 by rotating the adjustment screws clockwise about half way through their length as illustrated opposite. 2. Hook the canopy C onto the two screws 1. 3. To level the canopy on the wall rotate the adjustment screws S1 until the canopy is level and then tighten up the wall fixing screws to secure the canopy to the wall. 4. Before fitting the chimney to the canopy make the electrical connection as described in the section titled ‘ELECTRICAL CONNECTION’. been made, test the three speed fan and the spotlams 12 INSTALLING THE CHIMNEY HOOD DUCTING The hood is more effective when used in the extraction mode (ducted to the outside). When used in the extraction mode ensure the ducting spigot has been correctly fitted as illustrated. The ducting used must be . .....125 (5ins) or . .....150mm (6ins), flexible or rigid and must be manufactured from fire retardant material, produced to BS.476 or DIN.4102B1. The choice should be made by the installer. However, we recommend flexible ducting should only be used as an accessory as rigid ducting will provide better performance while reducing noise levels. The ducting flange D should be sleeved over the spigot A when using 125mm (5ins) ducting as the European ducting spigot is .120mm. Ducting kits can be obtained from Kitchen Specialist Distriutors, Builders Merchants and DIY stores. When the chimney hood is ducted to the outside the charcoal filter must be removed. RECIRCULATION If you are using the hood in the recirculation mode, ensure the charcoal filter is in position. FITTING THE RECIRCULATION DUCTING 1. Connect the duct P to the round outlet on top of the fan housing, which push fits into position, by pressing it downwards until it meets the fan casing. 2. Connect the spigot R on to the top of the duct P, which push fit into position, 13 D INSTALLING THE CHIMNEY HOOD by pressing it downwards until the two pieces meet. 3. Connect the two recirculation extension ducting pipes P1 on to the outlets on either side of the spigot R, which push fit into position, by pressing them horzont...
Otros modelos de este manual:Los aficionados - RMHDT90SS (1.21 mb)