Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
10. Acceptable for use over a bathtub or shower when installed in a GFCI protected branch circuit. 11. NEVER place a switch where it can be reached from a tub or shower. WARNING: DO NOT USE IN KITCHENS INSTALLATION INSTRUCTIONS CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE STARTING INSTALLATION. SECTION 1 Preparing the Exhaust Fan 1. Unpack fan from the carton and confirm that all pieces are present. In addition to the exhaust fan you should have: 1 - Grill 4 - Mounting Rails 1 - Damper Assembly (attached) 1 - Instruction/Safety Sheet 2. Remove the fan’s venturi assembly, which is secured in place with one screw through the venturi (Figure 1). This is a captive screw and will stay installed in the venturi. Keep the venturi assembly and the grill in the carton until needed so they do not get damaged or lost. Figure 1 4. Select the most convenient electrical knockout and remove using a straight- blade screw driver (Figure 2). SECTION 2 New Construction Figure 2 1. Install the mounting rails on the housing and position the housing next to the joist. Line up housing so that it will be flush with the finished ceiling. Secure the ends of the rails with screws or nails (not included) to the joists and slide the housing into the final position (Figure 3). Figure 3 Joist Housing Mounting Rails SECTION 3 Existing Construction 1. Set housing in position between the joist and trace an outline onto the ceiling material (Figure 4). Set housing aside and cut opening, being careful not to cut or damage any electrical or other hidden utilities. Install the rails on the housing and position the housing in the previously cut hole so that it is flush with the finished ceiling. Secure the ends of the rails to the joists (Figure 3). Figure 4 Joist 3. Choose the location for your fan. To ensure the best air and sound performance, it is recommended that the length of ducting and the number of elbows be kept to a minimum, and that insulated hard ducting be used. Larger duct sizes will reduce noise and airflow restrictions. This fan will require at least 6" of clearance in the ceiling or wall, and will mount through drywall up to 3/4" thick. The fan mounts to the joist using the mounting tabs on the side of the housing or between 16" or 24" on center joists using the 4 provided mounting rails. SECTION 4 Ducting CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL BUILDING CODES. 1. Connect the ducting to the fan’s duct collar (Figure 5). Secure in place using tape or screw clamp. Always duct the fan to the outside through a wall or roof cap. 210572118 Rev. B 5-06 2 of 4 Ducting Duct Collar Figure 5 Duct Collar Figure 5 NOTE: If damper detaches from unit, reattach by snapping the collar back onto the unit. It is designed to only fit one way. SECTION 5 Wiring CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE STARTING INSTALLATION. CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE MADE IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR NATIONAL ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN. 1. Run wiring from an approved wall switch carrying the appropriate rating. One neutral (white), one ground (green or bare copper), and one hot (black lead connected to the switch). Secure the electrical wires to the housing with an approved electrical connector. Make sure you leave enough wiring in the box to make the connection to the fan’s receptacle. 2. From where you have access to inside the fan’s junction box, connect the White wire from the house to the White wire from the fan’s receptacle. Connect the Black wire from the wall switch to the Black wire from the fan’s receptacle. Connect the ground wire from the house to the Green wire from the fan’s receptacle (Figure 6). Use approved methods for all connections. Figure 6 Ground Hot ...
Otros modelos de este manual:Los aficionados - BF120 (76.17 kb)
Los aficionados - BF150A (76.17 kb)