Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
Important: Your timed recording settings take effect when you turn off the power on the VCR. C_u_ion6f Aft e_en'_e_i_g _ PI_Cod_ _rrl6_re_ _ tH_i_f_i-m _tio_di_y_d_it_ _he I_P_O_ RAM RE_I EW if there i Using the VCR Plus+ system to record a program (by using the VCWs display) You can use the VCR Plus+ system to program the timer, observing the VCR's display, without turning on the power to the VCR and TV. Remote Control Illustration 1 Insert a blank or eraseable tape. The power comes on automatically and the tape indicator lights on the display. • When a cassette without its safety tab is inserted, playback starts automatically and VCR Plus+ recording won't operate. 2 Press the POWER button to turn the off the VCR. 3 The clock display switches to the indication shown on the right. • If eight programs have already been stored in memory, "FULL" will flash in the VCR's display for about five seconds. 4 Press the number buttons to enter the PlusCode number of the program you want to record. COrrect on e 5 Press the number buttons to enter the PlusCode number in the VCR's memory. The start time and channel will appear. Check the details of the program. • If you have installed a cable box (see page 26), the cable box output channel will appear in the channel display • If "Err" flashes for about five seconds, check the PlusCode number of the program and enter it again. Remote Control Illustration 6 Press the PROGRAM button to complete your programming or continue with additional programs. The delayed recording indicator will display on the VCR. This tells you that theVCR will automatically record at the times and dates you have programmed_ Nbteii cassette _as _ot b_eninse_ed or _ _assette with out safet_ _ 5 has Seen inse_ed the sure t_ i _assette wit5 safe_y _ab intact J When you have set up all the timed recordings you want: • Don't forget to load a videocassette 0Nith the safety tab still attached) to record on. • If you have installed a cable box (see page 26), turn on the cable box and select the channel you want to record on the cable box before recording starts. Important: Your timed recording settings take effect when you turn off the power on the VCR. Caution 0f VCRPI Aft ere nt eri ng aP!u sc 0den um be_iCh eCk the inf0 _ma_io n displayed wi_h the_!P R OGRAM REVI EW'_ff h__ei_ (are)_ hY ____ Ss_ p_0g_am(s)i p!e _se c_n ce!o __0 _re_t !t(t h_m) i P!_as_ rere _0 Page5 3i '_Rev!ew! _g wha_ Y0U haV_ PrOgram _ ed To go into the recording mode: 1. Press the POWER button to turn the VCR on. 2, Turn on "IV and select the video channel (3 or 4). 3, Pres the TAPE SPEED button to switch the recording mode. • Reviewing what you have programmed You can look back over any of the recordings you have preset and if you need to, clear out any of the programs. Normal programs will clear automatically once recording is complete, but daily and weekly setting must be cleared out manually. 1 Press the GUIDE button. The main on-screen menu will appear on the TV screen. 2 Press the (1) button for the PROGRAM REVIEW option. This brings up the screen setting for the first program. If you want to clear this program, press the CLEAR button to remove this program. Remote Control Illustration. 3 Keep pressing the (1) button to cycle through all the programs you have preset, • The screen will display the next program, if there are more, or it will switch back to the main menu. 4 Press the GUIDE button to end. The VCR remote control can be programmed to control many TV brands that are remote controlled. 1 Turn on the TV. 2 Point VCR remote control toward TV. 3 Press and hold the "TV" button. Remote Control Illustration. 4 Press the remote button corresponding to your TV brand as shown in the set-up chart. The TV channel will change to confirm that the remote control has been set. 6O Hitachi 1 Gold star 1 6 Panasonic 1 CH Zenith 2 Toshiba 7 Miteubishi CH Sony 3 Gold star 2 8 JVC 100lENT Magnavox 4 Panasonie 2 9 Sharp 1 VOL (UP) Sanyo 5 RCA 0 Sharp 2 AVX • Using the VCR remote to control your TV 1 Press the "TV" button on remote control. Remote Control Illustration. 2 Point VCR remote control toward TV. 3 Press buttons corresponding to the functions available on your TV remote control. The VCR remote control can be programmed to control many cable boxes brands that are remote controlled. You can easily change channels 1 Turn on the cable box. 2 Point VCR remote control toward cable box Remote Control Illustration. 3. Press and hold the "CATV" button. 4 Press the number button corresponding to your cable box a shown in the set-up chart. The cable box channel will change to confirm that the remote control has been set Jerrold 1 1 Zenith 5 Jerrold 2 2 Scientific 6 Atlanta Jerrold 3 3 Pioneer 7 Hamlin 4 Philips 8 Notei !f your cable bbx iS nbt listed on the Set_U >Cha_;tryal!thebu_o_S!!stedi_thecha_unti!the rem0_efo_you_ab!e b0x • Using the VCR remote to control your cable box. 1 Press the "CAW" button on the remote control. 2 Point VCR remot...