Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. 1/4” hex socket bit 4. Razor knife or similar 5. 10 mm deep socket 6. Pin router or similar 7. Audiovox VCP (AVP-7180 or equiv.) MATERIALS PROVIDED FOR INSTALLATION: June 7, 1999 INSTALLATION INSTRUCTION # 44-0033A Printed in the U.S.A ITEM Description QTY 1 SCREW, # 8 X 3/4" PPH 4 1 2 3 4 WELL NUT, 10-32 SCREW, 10-32 x 1" PPH WASHER, # 10 2 2 2 2 3 5 SCREW, # 10 X 1/2" HWH 4 4 6 7 SCREW, # 8 X 9/16" PWH CD/VCP MOUNTING BRACKET 8 1 5 8 HOUSING MOUNTING BRKT. 2 6 9 HOUSING TOP 1 10 STORAGE POCKET 1 11 HOUSING BOTTOM 1 June 7, 1999 INSTALLATION INSTRUCTION # 44-0033A Printed in the U.S.A. I. PREPARATION OF VEHICLE INTERIOR 2 IF VECHICLE IS NOT EQUIPPED WITH A FACTORY 10 DISC CD CHANGER, PROCEED TO STEP 5. FIGURE 1 1. Locate the O.E.M. CD changer housing mounted to the rear passenger side of vehicle. Remove and discard (4) four screws. Remove and discard housing by moving it upward and outward. See Figure 1. 2. Disconnect wiring from CD changer. See Figure 2. 3. Using a 10mm deep socket, remove and retain (4) four 6mm nuts which secure bracket to vehicle. See Figure 2. 4. Remove bracket from vehicle. Remove and retain (6) six screws which secure CD changer to bracket. See Figure 3. Lay CD changer in a safe place. Discard bracket. FIGURE 2 FIGURE 3 IF VECHICLE IS EQUIPPED WITH A FACTORY 10 DISC CD CHANGER, PROCEED TO STEP 6. 3 5. Locate the O.E.M. storage pocket mounted to the rear passenger side of vehicle. Remove and discard pocket by moving it upward and outward. See figure 4. FIGURE 4 6. Using a pin router, razor knife, or suitable tool, carefully trim plastic panel as shown to allow clearance for VCP bracket. See Figure 5. Caution: Before cutting panel, check for wiring or other componentry behind panel. Cut only where indicated. 7. Install (2) two housing mounting brackets (item 8 pg 2) as shown and secure using (3) three # 8 X 9/16" screws (item 6 pg 2) on each side. See Figure 6. FIGURE 5 FIGURE 6 4 8. Route video and audio cables to rear passenger side VCP location. See Figure 7. FIGURE 7 II. PREPARATION OF COMPONENTS FOR INSTALLATION 9. Remove and discard (2) two screws which secure mounting bracket (item 7 pg. 2) to housing. Insert CD changer (if equipped ) into mounting bracket and secure in original manner using (6) six O.E. screws. See Fig. 8. 10. Remove and discard (4) four screws from VCP. Loosely install (4) four #8 X 3/4” screws (item 1 pg. 2) in those locations. See Figure 9. FIGURE 8 FIGURE 9 III. INSTALLATION OF HOUSING IF VECHICLE IS NOT EQUIPPED WITH A FACTORY 10 DISC CD CHANGER, PROCEED TO STEP 13. FIGURE 10 11. Install CD player and bracket over O.E. studs and secure using original...
Otros modelos de este manual:Videocámaras - 50-0283x-018 SERIES (635.99 kb)
Videocámaras - 50-0283x-019 SERIES (635.99 kb)