Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Use positioning controls in the display first – if available. Pass RGB Input Sync Sync on Green Ext. Sync High/Low (Low sync is used with PAL sources where com posite video is applied as sync with RGB) Composite Sync on H On/Off Sync on Green On/Off (Default) (Comp. Sync on H and Sync on Green Functions are only available if RGB output is selected.) Output Format RGB(Default)/YCrCb/YPrPb Note: On 540p and 16:9HD models (Rev.2.4+), selecting YPrPb or YCrCb adds a Function for Tri-Level or Bi-Level sync and removes Sync-on- Green and Composite-Sync-on-H options from the menu list. HDTV standards require Tri-Level sync so it should be selected if there are any problems. Input Format Auto NTSC/PAL, NTSC, PAL, PAL N, PAL M I/R Setup - Press Enter Use this section to teach learning remotes the direct access codes. See the IR Setup section on page 10 for details. Test Patterns-Press Enter Use these patterns to adjust the image and processor. Use the Value key to select the different patterns. Once the pattern is selected press the Function key to return to the User Menu and then select the proper setup Function. Once adjustment is set, use the Function key to return to Test Patterns - Press Enter and select Test Patterns Off. Accessing the test patterns is easiest using the OSD. Off 100IRE Color Bars 100IRE Reverse Color Bars 10-Step Gray Scale Luma Ramp Cb Ramp Cr Ramp Green Red Blue Convergence Active Boarders SMPTE Color Bars 100IRE Window PLUGE User Mode-Press Enter 6 can be stored as a User Preset. can be stored as a User Preset. OPERATING INSTRUCTIONS These are the controls that are used most often. Noise Reduction 0-15, Factory 8 Detail 0-31, Factory 8 Tint 0-255, Factory 128 Color 0-255, Factory 128 Contrast 0-155, Factory 128 Brightness 0-170, Factory 128 Advanced Color System Factory/DVD Animation For some DVDs with computer animation, the Faroudja patented chroma edge processing circuits can be turned off. For most sources, the Factory setting should be selected. These settings Select OSD Functions: Press Function Change Values: Press Value On Screen Display Control of most functions can be done using the remote to interact with the OSD. Accessing the OSD • Press Menu button to bring up main Index. • Use Function keys to select an index and the available control menu drops down. • Press Function again to select an adjustment. • Use Value to adjust. The main menu drops away and a single line menu appears. • Use the Function keys return to the drop down menu. • Press Menu to recall the main index. • Press Menu again to remove OSD The OSD consists of four index tabs: INPUT PICTURE DISPLAY PATTERNS The Functions available for each index are listed below: IR REMOTE AND OSD OPERATION There are four ways to control the unit: from the front panel, with the remote control buttons, using the On-Screen-Display with the remote and via RS232. Controlling from the front panel or the remote requires cycling through the available functions. If direct access IR control is needed, the unit can teach learning remotes via the IR flasher. See the IR Setup section. When the unit first powers up it will go through an initializing procedure and then display the output resolution. The remote control allows for easy operation by simple navigation through the On Screen Display (OSD)menus. Repeated Pressing of a button toggles through the available choices. Power On/Off: Press Power Select Presets: Press Preset Select Input:s Press Input Mode Activate OSD: Press Menu INPUT Formats Input Select: Video-S-Video-YCrCb-RGB-PassThru Aspect Ratio* 4:3-Letterbox-Anamorphic Presets- Recall: Factory-1-2-3-4 Store: 1-2-3-4 To store a preset: • Select the proper input. • Make all required adjustments. • Use the Function keys to select Store 1 2 3 4. • Use the Value keys to select the desired preset • Press Enter *Aspect Ratio Selection Press the Aspect Ratio button to toggle between the different choices. The aspect ratio selected needs to match the aspect ratio of the source. 7 RS232 NOTE: When using a Wide Angle screen a 4:3 source will have black bars on the left and right of the image. If filling the entire screen is desired, select Letterbox. The image will fill the screen but the top and bottom 1/3 of the image will be cut off. Note: Anamorphic on a 4:3 screen is not available on units with scan rates below 720p. PICTURE Use these commands to fine tune the image Brightness Contrast Tint Color Detail Noise Reduction NOTE: Adjusting Detail – The Detail and Noise Reduction settings have been optimized for the scan rate and resolution of the NR Series for most sources. However, the viewers tastes and the types of software used may require making –adjustments of these settings to fine tune the image. These controls are very effective to either increase detail or to help clean up poor quality video material. It is recommended that adjustments be made in small increments until the desired results are achieved. It is important to not use too mu...
Otros modelos de este manual:Videocámaras - Native Rate Series Plus (119.78 kb)