Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Cannot copy scenes on the SD card by connecting to other equipment with the USB cable. .Other equipment might have not recognized the SD card. Unplug the USB cable once, and reconnect it. VQT2M51 . If scenes do not change smoothly when played back on another device The images may be still for several seconds at the joins between the scenes if the following operations are performed when multiple scenes have been continuously played back using another unit. . Just how smoothly the scenes will be played back depends on the playback unit. Depending on the unit used, the images may stop moving and become still for a moment even when none of the following conditions are applicable. . A continuous recording of motion picture data that exceeds 4 GB may momentarily stop at every 4 GB of data when played back with another device. . It may not play back smoothly when the editing of scenes was done with the HD Writer AE 2.0, but it will play back smoothly if you set the seamless settings in the HD Writer AE 2.0. Refer to the operating instructions for the HD Writer AE 2.0. Principal reasons for not playing back smoothly . When the scenes were recorded on different dates . When scenes lasting under 3 seconds have been recorded . When PRE-REC was used for recording . When deleting scenes . When selected scenes are copied between an SD card and the built-in memory/ HDD . When selected scenes are copied to a disc in a connected DVD burner. . When scenes recorded with more than 99 scenes on the same date VQT2M51 Others Others Cautions for use About this unit The unit and the SD card become warm during use. This is not a malfunction. Keep the High Definition Video Camera as far away as possible from electromagnetic equipment (such as microwave ovens, TVs, video games etc.). . If you use the High Definition Video Camera on top of or near a TV, the pictures and sound on the High Definition Video Camera may be disrupted by electromagnetic wave radiation. . Do not use the High Definition Video Camera near cell phones because doing so may result in noise adversely affecting the pictures and sound. . Recorded data may be damaged, or pictures may be distorted, by strong magnetic fields created by speakers or large motors. . Electromagnetic wave radiation generated by microprocessors may adversely affect the High Definition Video Camera, disturbing the pictures and sound. . If the High Definition Video Camera is adversely affected by electromagnetic equipment and stops functioning properly, turn the High Definition Video Camera off and remove the battery or disconnect AC adaptor. Then reinsert the battery or reconnect AC adaptor and turn the High Definition Video Camera on. Do not use the High Definition Video Camera near radio transmitters or high-voltage lines. . If you record near radio transmitters or high-voltage lines, the recorded pictures and sound may be adversely affected. Make sure to use the supplied cords and cables. If you use optional accessories, use the cords and the cables supplied with them. Do not extend the cords and the cables. Do not spray insecticides or volatile chemicals onto the unit. . If the unit is sprayed with such chemicals, its body may be marred and the surface finish may peel off. . Do not leave rubber or plastic products in contact with the unit for a long time. When you use the unit in a sandy or dusty place such as a beach, do not let sand or fine dust get into the body and terminals of the unit. Also, keep the unit away from sea water. . Sand or dust may damage the unit. (Care should be taken when inserting and removing a card.) . If sea water splashes onto the unit, wipe off the water with a well wrung cloth. Then wipe the unit again with a dry cloth. When carrying the unit, do not drop or bump it. . A strong impact can break the unit’s casing, causing it to malfunction. Cleaning . Before cleaning, detach the battery or pull the AC cable from the AC outlet, and then wipe the unit with a soft, dry cloth. . If the unit is very dirty, dip a cloth in water and squeeze firmly, and then wipe the unit with the damp cloth. Next, dry the unit with a dry cloth. . Use of benzine, paint thinner, alcohol, or dishwashing liquid may alter the camera body or peel the surface finish. Do not use these solvents. . When using a chemical dust cloth, follow the instructions that came with the cloth. VQT2M51 Do not use th purposes .This unit intermitt continuous commer prolong .In certa cause the uni malfunc discourage When you a for an extended .When s cabinet, a desiccan Whe uni .F f be bu - da av .W t - dis . To phys connect t [FORMA from the menu, the delete about 3 memory select [Y on-screen ins lly format the HDD, connect the he AC adaptor, select EDIA] # [HDD] from the en press and hold the delete screen below for about When the HDD data deletion ppears, select [YES], and then -screen instructions. after the data in your built-in r HDD carefully. Panasonic will responsible in the unlikely ivate data is divulg...