Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Releasing the button stops the search. Press RECORD/PAUSE to continue recording. (209 • During Edit Search, the picture will have a mosaic pattern. The sound will be muted when using reverse visual search. • Make sure the SP/LP tape speed setting is the same as the recording to eliminate distortion during edit search. /"r-WI.-, 32 For assistance, call 1-800-211-PANA(7262) Camera Recording / Remote Control You can go directly to a blank portion of tape and start recording exactly where you left off. MENU Button JOG KEY 1 2 3 4 5 Set the POWER to VCR. • The POWER lamp lights red. • Be sure POWER is fully turned to VCR position. Press MENU to display the VCR mode menu screen. Rotate JOG KEY to select OHM] EEEB, then press JOG KEY to display the VCR PLAY MODE menu screen. BJSEARCy. Rotate JOG KEY to select [_ in the VCR PLAY MODE menu (page 25). Press JOG KEY to select ON. » “BLANK” will appear on the screen. POWER Switch Remote Control (Optional, page 72) You can operate the major functions of your Palmcorder from up to approximately 16 feet (5 m) away (indoors). Aim the IR Remote Control toward the front of the Palmcorder and press the desired buttons (Remote Sensor is located under the lens). To operate Camera functions: Set POWER to CAMERA. To operate VCR functions: Set POWER to VCR. Controlled Functions Rec/Pause (page 30) Tele (Zoom) (page 51) Wide (Zoom) (page 51) Date/Time (page 27) Reset (page 60) PhotoShot (page 52) Display On TV (page 40) Counter/Time Code (page 26) Audio Dubbing (page 59) Record (page 62) Menu (page 20) Play (page 35) FF/Search (page 36) REW/Search (page 36) Pause/Select (pages 20, 36) Stop/Set (pages 20, 35) Slow/Frame Advance (Forward) (pages 36, 38) Slow/Frame Advance (Backward) (pages 36, 38) Index Search (Forward) (page 39) Index Search (Backward) (page 39) Speaker Volume (page 35) 33 Basic Operation Remote Control (Optional) Remote Controlling Two Palmcorders You can control any two Panasonic Digital Video Camcorder with one Remote control (Optional, page 72). In order for the remote to distinguish between the two units, it is necessary to set one of the Palmcorders to VCR 2. On the remote, press VCR 1 or VCR 2 to control the desired Palmcorder. 1 2 3 Set the POWER to VCR or CAMERA. • The POWER lamp lights red. • Be sure POWER is fully turned to VCR or CAMERA position. Press MENU to display the VCR or CAMERA mode menu screen. For VCR 2 : Press these buttons at same time. For VCR Press these buttons at same time. When the Palmcorder and remote are not set to the same mode (VCR1 or VCR2), “CHECK REMOTE MODE (REMOTE)” will appear. r ---- REMOTE 4. ./ i4 'GÄMERÄ1 Rotate JOG KEY to select | mmE in the CAMERA mode menu screen or RStefcl ifli/jyy I ft [o] p]3l in the VCR mode menu screen, then press JOG KEY to display the CAMERA SET-UP or VCR PLAY MODE menu screen. ВЕМШ1Е Rotate JOG KEY to select | and then press JOG KEY to select VCR 2 on one Palmcorder (pages 23, 25). Leave the other Palmcorder set to VCR1. Set the Remote Control (Optional, page 72) to VCR 1 or VCR 2 to correspond with the Palmcorder you wish to control. (See illustration at left.) After replacing the Remote Control Battery, the remote will default to VCR 1. Replace the Battery О 1 Insert a slender pointed object, such as the tip of a ball-point pen into the slot so that it fits into the hole (as shown a). Then, while sliding to the right, pull the Battery Tray out with your fingernail. Insert the battery into the Battery Tray with the © mark facing down. Do not reverse the polarity. Insert the Battery Tray. Replace battery with Panasonic PART NO. VSBW0004 (CR2025) only. Use of another battery may present a risk of fire or explosion. Caution-battery may explode if mistreated. Dispose of used battery promptly. Keep away from children. Do not recharge, disassemble or dispose of in fire. 34 For assistance, call 1-800-211-PAN A(7262) Playback your Recordings Playback using the LCD Monitor You can also use the LCD monitor to playback your recording. VOLUME KEY LCD-OPEN Button Before you begin... • Connect the Palmcorder to a power source (pages 12,13). • Insert a recorded cassette. • Set Power to VCR. 1 2 REWIND PLAY etc. for viewing. Rotate the LCD Monitor 180° and swing it up against the Palmcorder body as shown. Press LCD-OPEN to unlock the LCD monitor and swing open. Press REWIND/SEARCH to rewind the tape. O Press PLAY to start playback. To adjust the volume: Hold down VOLUME KEY until the volume setting screen appears (page 27). Then rotate VOLUME KEY to adjust the volume of the built-in speaker. To disappear the volume setting screen, hold down VOLUME | KEY again. •Adjust the picture on the LCD monitor if needed (page 31). 4 Press STOP to stop playback. • When the tape reaches its beginning during rewind or rewind search, it will stop automatically. • If you press PLAY for more than 5 seconds, th...