Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
(See pages 11,12.) 1 Cassette Compartment Cover Slide TAPE EJECT to open the Cassette Compartment Cover. Insert a cassette record tab up, window side facing out. O Press PUSH TO CLOSE mark to close the Cassette Compartment Cover. • To remove the cassette... Slide TAPE EJECT to open the Cassette Compartment Cover and pull the cassette tape straight out. Hint to locate recording position when inserting cassette • When you insert a partially recorded cassette, use the Edit Search Function (see page 24) to visually confirm the point at which you want to start a new recording. Especially advisable when you want to add a recording to a tape that is already full. Note • If hand strap is tight it may prevent Cassette Compartment Cover from fully opening for tape insertion or ejection. Loosen hand strap if necessary • When inserting the cassette, make sure it faces in the right direction and then push in completely. To brighten the natural colors in a scene. Built-in Light Mount Before you begin- • Connect the Palmcorder to a power source. (See pages 11, 12.) • Set POWER to CAMERA. 1 Slide Light into the Built-in Light Mount. Be sure it locks into place. 2uGHT Button VF \--- —y ^ Press LIGHT to turn Note ON or off: operating time. Be sure to provide adequate ventilation if using Light in a hot environment for an extended period. Be sure LIGHT is set to OFF when not in use. Do not attempt to lift or carry the Palmcorder by holding the Enhancement Light. If light bulb needs to be replaced, take Light to your nearest authorized servi center. LIGHT RELEASE Button To remove the Light: Press LIGHT RELEASE and slide the Light out of the mount. r Caution:- This light becomes hot during operation. Make sure nothing covers the Light during operation. 7 I Undo the two strap ends from their buckles Remove the buckle from one end of the strap ^ Thread the strap (with no buckle) through the Light Holder so that it faces outward Then, reinsert the buckle 1 2 Loosen the strap from the Buckle and create a loop Pull the strap firmly through the Buckle to shorten or lengthen the strap ^ 1 Insert the Light into the Light Holder for Storage To remove the Light, press LIGHT RELEASE and slide Light out of the holder 2light RELEASE Button Thread the strap ends through the Strap Attachment Rings Reinsert the strap ends through their buckles • Make sure the straps are not twisted Q O \ KaBagai@(ö)| Adjust the length of the Hand Strap to the size of your hand as illustrated tkäü@©a[p) Attaching the Lens Cap Cord to the Hand Strap Remove the Hand Strap from the front clasp and thread the Strap through the loop tn the Lens Cap Cord Reattach the Hand Strap 8 For assistance, please call: 1-800-211 -PAN A(7262) or send e-mail to: consumerproducts@panasonic.com 1 QjpB^giD3iiaiSj^[^EQs 1 Before you begin- • Charge the Battery. (See page 11.) click. iMaftcgBgggBTi 1 Set POWER Switch to CAMERA. PUSHTO CLOSE mark Slide TAPE EJECT Switch to open the Cassette Compartment Cover. Insert a cassette record tab up, window side facing out. • Make sure the record tab is closed. (See page 6.) Protection Film Remove the Protection Film before use. Press PUSH TO CLOSE mark to close the Cassette Compartment Cover. 9 When the LCD monitor is fully open, the Viewfinder automatically turns OFF. Adjust the Vision Adjustment Control to your eyesight. Viewfinder Set POWER Switch to CAMERA. Press LCD-OPEN Button to unlock the LCD monitor. Swing it fully open and adjust the angle. When the LCD monitor is fully open, the Viewfinder automatically turns OFF ^ Press REC/PAUSE Button to start recording. Press REC/PAUSE Button again to pause recording. Before you begin- Charge the Battery. (See page 11.) Press LCD-OPEN Button to unlock the LCD monitor. Swing it fully open and adjust the angle. Set POWER Switch to VCR. Press STOP Button to stop playback. Press PLAY Button to start playback. 10 For assistance, please call : 1-800-211 -PAN A(7262) or send e -mail to : consumerproducts@panasonic.com (gCDgD^®DS®giQa^(jfe$(SOT' flte^&jjsnfia? 1 Connect and plug in the Power Cord as shown • POWER Lamp wilt light • Remove the DC Cable, if attached, from the adaptor i Attach the Battery as shown to charge • CHARGE Lamp lights up It goes out when charging is complete (approx 1 hour) Expect approx 1 hour 30 minutes of operation (EVF usage) when fully charged 1 Remove the Battery Slide the Battery out and then lift up About the Flashing of the CHARGE Lamp • Charge the Battery within an ambient temperature range of 10 °C and 30 °C • If charging is done in extreme low or high temperatures, Battery charge time increases CHARGE Lamp flashes when • The Battery is being charged, but charging is taking longer than normal • Charging is not possible Remove the Battery once, wait a short time, then re-attach it for charging 2 Insert the Battery Pack and slide it down until it ...