Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
This is a normal characteristic of the CCD pick-up device. Try to avoid this when possible. r PAUSE Record/Pause mode. With the Viewfinder Eye Cup against your eye, adjust the Vision Adjustment Control to your eyesight. Slide the TAPE SPEED Selector to SP or SLP (refer to page 10). Press RECORD/PAUSE to start recording. Press the RECORD/PAUSE again pause the recording. Set the Power switch to OFF after recording is finished. • To remove the cassette In Record/Pause mode, slide the TAPE EJECT switch (refer to page 10). 19 Basic Operation Camera Recording Stand-by Quick Release Whenever the Palmcorder is left in RECORD/PAUSE mode for 5 minutes, it will automatically switch to Stand-by mode to conserve energy. Activating the Stand-by Quick Release feature allows you to release the Stand-by mode and resume recording by simply pressing the RECORD/PAUSE button. If this feature is not activated, it is necessary to turn the Palmcorder OFF and back on to CAMERA to start recording again. The default setting from the factory is set to theEEEBEBBnSmode. DISPLAY RECORD/PAUSE Before you begin... • Connect the Palmcorder to a power source. ♦ Insert a cassette with record tab (see page 10). Continue holding down the UP ▲ button before and after turning the POWER switch to CAMERA until the STAND-BY RELEASE menu screen is displayed. Press UP A or DOWN ▼ to select or I ACTIVEE1 NON-ACTIVE STAND-BY RELEASE BY RECORtVPAUSE KEY ACTIVE lfi.lg.MEH SELECT: PUSH T/A KEY SET : PUSH DISPLAY KEY, v_y ACTIVE You can resume recording from Standby mode by pressing the RECORD/ PAUSE button. NON-ACTIVE You must set the POWER switch to OFF, and then to CAMERA to release the Stand-by mode. Press DISPLAY to set your selection and exit this screen. 20 I Camera Recording Easy Edit Stand-by If you stop recording but plan to resume within 24 hours, use the Edit Standby feature to make a smooth transition between scenes. -g L Press RECORD/PAUSE while recording. ^Set the POWER switch to OFF and _ leave the cassette in the Palmcorder. t/When ready to resume recording, set the POWER switch to CAMERA and press RECORD/PAUSE. Note: • If it is going to be longer than 24 hours before you resume recording, you will need to use the] manual Easy Edit feature described below. POWER Switch Manual Easy Editing For proper continuity when taping from the Stop mode, or after changing the Battery Pack. Set the POWER switch to VCR. ® Press REWIND/SEARCH to go back a few seconds on the tape. ® Press PLAY to review the picture on the Viewfinder. © Press STILL at the location you wish to continue your recording. Set the POWER switch to CAMERA. Press RECORD/PAUSE to continue recording. 21 Basic Operation Play Back your Recordings Playback using the EVF Before you begin... • Connect the Palmcorder to a power source. • Insert a recorded cassette. UP ▲ DOWN T Special Effects Playback Rapidly Locate a Scene Press FAST FORWARD/SEARCH or REWIND/SEARCH for rapid visual search. Press again, or press PLAY to resume normal speed. View a Still Picture Press STILL to freeze the picture. Press again to resume normal playback. This feature works best in SLP mode (see pages 10,19). Note: • During search playback, horizontal noise bars will appear and there will be no audio. * To protect the tape and the video heads, your Palmcorder’s operating modes will revert as follows: STILL-► STAND-BY after 5 minutes. STANDBY —► POWER OFF after 5 minutes when using a Battery Pack. ■ When the tape reaches its end during playback, or fast forward, it will rewind automatically. 22 Set the POWER switch to VCR. ® Press the REWIND/SEARCH button to rewind the tape. ® Press PLAY to start playback. © Press STOP to stop playback. Auto Play When the POWER switch is set to VCR, playback will automatically begin if the record tab has been removed on the cassette. Search Speed Standard Play (SP) Search is about 3 times the normal speed, and Super Long Play (SLP) Search is about 9 times the normal speed. Tracking Control Auto Tracking Continuously analyzes the signal of each recording for optimum picture quality. Manual Tracking To minimize the noise in some recordings, manual tracking may be necessary. In Playback mode: Press UP ▲ or DOWN ▼ until picture clears. Press DISPLAY to return to Auto Tracking. f > s 1,1 V Play Back your Recordings TV Playback or Viewing Your Palmcorder may be connected to a TV to play back tapes or to view what you are recording. Q TV with AUDIO/VIDEO IN Jacks. ) Back of TV: To Audio In Audio/Video Cable (Supplied) To Audio/Video Out Q TV without AUDIO/VIDEO IN Jacks. ^ To Audio/ Video Out Before you begin... • Connect the Palmcorder to a power source. 1 Set the POWER switch to VCR for tape playback. Or, set to CAMERA to view what your Palmcorder is recording. ^Turn the TV ON and set it to LINE ! INPUT. Check your TV operating instructions. Note: If your TV has...