Votos - 1, Puntuación media: 3 ( )

Fabricar: Panasonic Tamaño del archivo: 3.32 mb Nombre del archivo: AJD900WP.PDF Idioma del manual:

The center marker and safety zone marker, etc. are also displayed. When the MENU SET/OFF switch is set to OFF, items set to SET at the VF DISPLAY page of the setting menu and using related switches appear at the top and bottom of the screen. Messages informing of the setting contents or of the adjustment course or results can also be displayed for approximately 3 seconds when settings are changed, during the course of adjustments, or after adjustments have been completed. •See “Selecting Display Items" (page 56) for selecting display items, “Display Mode and Setting Change Message” (page 57) for the setting change message, and “Setting the Marker Displays” (page 58) for the marker displays. The display positions of all items which can be displayed are shown in the figure below. 1. Extender display 2. Shutter speed/mode display 3. Remaining tape length display 4. Remaining battery level display 5. Filter display 6. White balance memory display 7. Gain value display 8. Audio level display 9. Iris value display 10. Warning display 11. Safety zone marker 12. Center marker 13. Super iris ON display 14. MARK1/MARK2 display 15. TCG (Time Code Generator) display -53- Status Displays Inside the Viewfinder Screen 1 Extender display This is displayed when the lens extender is being used. 2 Shutter speed/mode display This displays the shutter speed or shutter mode setting. OFF: The shutter is not used. 1/100, 1/120, 1/250,1/500,1/1000, 1/2000: Shutter speeds (seconds) during standard mode. 1/30.2-1/250 (SYNCHRO SCAN): Synchro scan mode is selected. SUPER V: High vertical resolution mode is selected. 3 Remaining tape length display This indicates the remaining tape length (minutes) for the VTR during recording. Remaining tape length display Remaining tape length display (25 Mbps) (50 Mbps) Display Remaining tape length F—60 Full to 60 minutes 60-55 60 to 55 minutes 55-50 55 to 50 minutes 50-45 50 to 45 minutes 45-40 45 to 40 minutes 40-35». 40 to 35 minutes 35-30 35 to 30 minutes 30-25 30 to 25 minutes 25-20 25 to 20 minutes 20-15 20 to 15 minutes 15-10 15 to 10 minutes 10-5 10 to 5 minutes 5-0 5 to 0 minutes Display Remaining tape length F-30 Full to 30 minutes 30-25 30 to 25'minutes 25-20 25 to 20 minutes ro 0 01 20 to 15 minutes 15-10 15 to 10 minutes 10-5 10 to 5 minutes 5-0 5 to 0 minutes The “5-0" display flashes when there is less than 3 minutes of tape remaining. 4 Remaining battery level display When an Anton Bauer Digital Magnum Series battery is used to supply power to the unit, the remaining battery level is displayed numerically (%). 5 Filter display This displays the type of filter selected. 6 White balance memory display This displays the selected white balance automatic adjustment memory. A: The WHITE BAL switch is set to A. B: The WHITE BAL switch is set to B. P: The WHITE BAL switch is set to PRST. ( Gain value display This displays the image amplifier gain setting (dB) set by the GAIN switch. When using an Anton Bauer Digital Magnum Series battery, the remaining battery level display continues to display the level for the Anton Bauer battery even if power supply is switched to an external power source near the end of the battery’s power. However, note that the unit operates according to the external power source. -54- 8 Audio level display This displays the audio CH1 level. During sine wave input, the audio level display corresponds roughly to the VTR level meter display as follows. Audio Channel 1 Level Display ^ VTR Level Meter "40 “30 -25 *20 -15 -10 “5 0 9 Iris value display This displays the approximate iris setting (F number). 10 Warning display This displays the black balance, white balance, auto knee function, super iris, super gain and other warning displays. 11 Safety zone marker This indicates the 80% or 90% (setting when shipped from the factory) range for the viewfinder screen area. The screen area percentage is selected at the MARKER page of the setting menu. •See “Setting the Marker Displays” (page 58) for a detailed description. 12 Center marker This indicates the center of the viewfinder screen. This marker is displayed when set to ON at the MARKER page of the setting menu. 13 Super iris ON display This indicates that the super iris is ON. 14 MARK1/MARK2 display If the MARK switch is pressed while the Picture Link function is used, M1 or M2 appears to indicate the significance of the information concerned. Nothing is displayed when this function is not required. 15 TCG display This displays the time code generator value. 1) Iris value display The iris value is displayed when using a lens with the iris value display function. -55- Status Displays Inside the Viewfinder Screen Selecting Display Items The items to be displayed oh trie viewfinder screen can be selected by switching the display ON/OFF setting independently for each item at the VF DISPLAY page. The items which can be select...

Descargar ahora

Introduzca dos números de la imagen: