F-RUN : Set here to have the time code run all the time regardless of the VTR’s operation. This position is used to align the time code with the time or externally lock the time code. SET : Set here when the time code or user’s bit is to be set. R-RUN : Set here to have the time code run only during recording. The time code on the tape with scene-toscene continuity is recorded continuously. 20 Power supply A battery pack or an AC power source can be used as Using the Anton/Bauer battery pack this unit’s power supply. To use the battery pack, there is a choice of three makes of batteries, namely: OPanasonic OAnton/Bauer OSony Batteries of other makes can also be supported by changing the setting menu but no guarantees are made for the system when they are actually used with this unit. Before using the battery pack, recharge the battery using the battery charger. (For details on the recharging method, refer to the operating instructions of the battery concerned.) 1 Attach the battery pack. Insert the pack in the direction shown by the arrows, and then slide it into position. Power output socket for lighting Lighting control switch 2 To detach the battery, pull the battery mount removal lever all the way down, and slide the battery pack in the direction shown by the arrow. Removal lever Battery pack An intelligent battery system and ultra light system are supported. The remaining battery charge displayed inside the viewfinder is usually shown as a percentage of the full charge, but when the battery charge is nearly completely dissipated, the percentage display is replaced with a voltage display. 21 22 Power supply Using the Panasonic AU-BP402 battery pack ODo not pull the rubber cap forcefully. OWhen mounting the battery case, take care not to pinch the connecting cord. 1 Detach the battery mount. 3 Attach the AU-M402H battery case. Open the battery case cover, and raise it above the rubber cap: screw holes will now be visible. Tighten the screws using a screwdriver, then attach the case to the unit and tighten the screws fully. 2 Connect the AU-M402H battery case connector with the connector on the unit. 4 Connect the plug on the battery pack to the connector inside the case, and insert the battery pack. Before connecting or disconnecting the plug, be absolutely sure to turn off the unit’s power. 23 Power supply Using the Sony NP-1 battery pack 1 3 4 2 When mounting the battery holder, take care not to pinch the connecting cord. 1 Detach the battery mount. See page 22. 2 Attach the accessory battery mounting connector. 3 Attach the Sony battery holder. As shown in the figure, attach the battery case with the cover detached and then the detached cover. 1Tighten the mounting screws. 2Tighten the power contact screws. 3Insert the top of the detached cover in the direction shown by the arrows. 4Align the holes in the bottom of the cover (metal part) with the holes at the bottom of the case, and use the battery holder screws to attach the case to the battery mounting connector. Using the Sony BP-90 battery pack 1 Attach the accessory battery mounting connector. 2 Attach the battery case for the BP-90. 1. Tighten the mounting screws. 2. Tighten the power contact screws. 3. Insert the top of the detached cover in the direction shown by the arrows. 4. Align the holes in the bottom of the cover (metal part) with the holes at the bottom of the case, and use the screws to attach the case. 24 Using an AC power supply When the AJ-B75 AC adapter is used OCheck the pin signals of the EXT DC IN socket when using an external power supply other than the AJ-B75 AC adapter. (DC 12 V, 8.5 A) OPower from the AC adapter takes precedence when both a battery pack and AC adapter have been connected. OWhen using the AC adapter, be absolutely sure to first set the power of the AC adapter to ON and then set the unit’s power switch to ON. If the power is turned on in the reverse sequence, the output voltage of the AC adapter will rise gradually, and the unit may malfunction as a result. 1 2 3 4 1 Connect the DC OUT connector on the AJ-B75 AC adapter to the EXT DC IN socket on the unit. EXT DC IN socket 2 Set the power of the AC adapter to ON. 3 Set the unit’s power switch to ON. Pin no. Signal 1 GND 2, 3 == 4 +12 V Power supply OBefore connecting or disconnecting the plug, be absolutely sure to turn off the unit’s power. OWhen attaching the battery case or holder, take care not to pinch the connecting cord. Using the Sony BP-L60/L90 lithiumion battery 1 Attach the accessory battery mounting connector. (Refer to the previous page.) 2 Attach the battery holder for the lithium-ion battery. 1. As shown in the figure, detach the battery clamp, and attach the holder using the mounting screws. 2. Tighten the power contact screws. 3. Attach the battery clamp. Battery clamp Attaching the lens 1 Raise the lever for securing the lens, and detach 4 Push the cable into the cable clamp, and connect it...
)
