The buzzer sounds when the CALL button has been pressed or when a tracing memory operation (record, play or change) is started, suspended or ended. AUTO RUN setting (START No., END No., INTERVAL) This menu item enables the presets of the pan/tilt head to be repeated automatically. START No. (1 to 50): This sets the first number of the preset to be repeated. END No. (1 to 50): This sets the last number of the preset to be repeated. INTERVAL (1s to 30s): This sets the stop time at the preset position. Up to 30 seconds can be set in 1-second increments for the stop time. OPERATE (STOP/RUN): When RUN is selected, the presets from the START No. to STOP No. are played repeatedly; when STOP is selected, operation stops. When the PAN/TILT lever is operated, STOP is selected automatically, and operation stops. SD CARD setting The menu setting data of this control panel, the preset memory data of the pan/tilt heads and the setting data of the cameras can be stored on SD memory cards. If the MENU button is pressed while STORE is displayed, the display changes to EXECUTE, and the settings are saved on the SD memory card. The process is completed when the EXECUTE display is cleared from the screen. If the MENU button is pressed while LOAD is displayed, the display changes to EXECUTE, and the settings on the SD memory card are called and loaded into the unit, pan/tilt head and camera. The process is completed when the EXECUTE display is cleared from the screen. . Confine the use of the SD memory card to this unit only, and refrain from using it with a personal computer, digital camera or other device. . Do not eject the SD memory card, turn off the power or set the OPERATE switch to OFF while EXECUTE is displayed. . The tracing memory data is not stored. 32 Pan/Tilt Control Panel AW-RP400 How to mount the AW-RP400 in a rack . The AW-RP400 is 320 mm wide. If it is to be installed in a full-size rack (which accommodates units totaling 420 mm in width), provide panels or other parts to supplement the AW-RP400’s width so that it will fill the rack width-wise. . If the AW-RP400 is joined to the AW-CB400, the resulting width will be equivalent to that of the full width of the rack (which accommodates units totaling 420 mm in width). 1 Use the accessory mounting screws (M4!8 mm) to attach the rack-mounting adaptors. Rack-mounting adaptor AW-RP400 320mm Accessory mounting screws (M4!8 mm) 4 pcs AW-RP400 33 Pan/Tilt Control Panel AW-RP400 How to change the position of the connector panel The position of the connector panel can be changed from the rear panel to the bottom panel. . Before changing the position, turn off the power. Screws!5 (bottom panel) 1 Remove the five bottom panel screws, and remove the blank panel. panel. Remove the blank Screws!5 (rear panel) 2 Remove the five rear panel screws, and remove the connector panel. Remove the connector panel. Screws!5 (rear panel) 3 Secure the blank panel to the rear panel using the screws. 4 Remove the two rubber feet from the blank panel. Screws!5 (bottom panel) Blank panel Remove the two rubber feet. 5 Secure the connector panel to the bottom panel using the screws. Connector panel 34 Pan/Tilt Control Panel AW-RP400 How to replace the zoom switch . Before replacing the zoom switch, turn off the power. 1 Remove the four screws that secure the zoom lever. Screws!4 2 Pull out the zoom lever, disconnect the two cables from the circuit board inside, and remove the zoom lever. 3 Plug the two cables extending from the zoom switch into the connectors on the circuit board inside. 4 Secure the zoom switch using the four screws. Screws!4 AW-RP400 35 Pan/Tilt Control Panel AW-RP400 Replacing the consumable parts The joysticks and zoom switch are consumables. Replace them if they are not working properly. Ask your dealer to do the replacement work. 36 Pan/Tilt Control Panel AW-RP400 Specifications Supply voltage: DC 12.0 V Power consumption: Approx. 13 W 1 indicates safety information. Input connectors DC 12V IN: XLR, 4 pins CONTROL IN FROM ROP: D-SUB 29-pin, cable supplied with AW-CB400 remote operation panel CONTROL IN FROM RCB: 10-pin round connector, cable supplied with WV-CB700A EXT CONT IN: RJ45, additional AW-RP400 control signal input; 10BASE-T straight cable (UTP category 5), max. 500 meters REMOTE: 50-pin D-SUB connector, external control input, AW-CA50T9 Output connectors CONTROL OUT TO PAN/TILT HEAD: RJ45, pan/tilt head control signal output; 10BASE-T straight cable (UTP category 5), max. 500 meters MONI SEL OUT: RJ45, monitor switching signal output; 10BASE-T straight cable (UTP category 5), max. 50 meters EXT CONT OUT: RJ45, additional AW-RP400 control signal output; 10BASE-T straight cable (UTP category 5), max. 500 meters Input/output connectors INCOM (top panel): XLR, 4 pins TALLY/INCOM: D-SUB, 15-pin TALLY: Contact input (Do not apply a voltage in excess of 5V to this connector.) INCOM: 4-wire system Switch functions: Master/slave switching, OPERATE control, home po...
)
