Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Match the four grooves on the camera with the four projections on the dome cover. 2-8. Attach the dome cover to the camera by turning this cover clockwise so that the window in the dome cover matches the camera head. ADJUSTMENT 1. Panning The Panning table can be moved between the guide lines. 2. Tilting the camera The tilting angle is shown below. Note: Uprighting the picture on the monitor screen is usually necessary. (Refer to 3. Uprighting the picture.) 3. Uprighting the picture Loosen the 2 lens holders and bring the picture in an upright position on the monitor screen by turning the camera head. 4. Focusing Precaution: The focus adjustment should be done at the same time as the camera angle adjustment. Focus lock lever 4-1. Loosen the zoom lock lever. 4-2. Set the angular field of view according to the scene desired. 4-3. After setting the angular field of view, tighten the zoom lock lever. 4-4. Loosen the focus lock lever. 4-5. Set the correct focus by turning the focus ring. 4-6. After setting the correct focus, tighten the focus lock lever. 4-7. After adjusting the angular field of view and focus, attach the dome cover to the camera body. -10- SYSTEM CONNECTION Shown below is an example of a basic system connection. Video Multiplexer o ^ E ^ m ebb' -loi B E •aa-a-a T=T RS-232C/Wired □ □ □ Time Lapse VCR - AUX — Alarm I I I I Spot Monitor Live 1-16ch Multiscreen Monitor Live 1-16ch Playback 1-16ch -11- SETUP 1. CAMERA SETUP MENU This camera utilizes a user setup menu that is displayed on-screen. The setup menu contains various items that form a tree-type structure as shown below. It is described in the following section : "2. SETUP OPERAtlON.” 2. SETUP OPERATION This camera utilizes a user setup menu (CAM SET UP) that is displayed on the monitor. To set items on the CAM SET UP menu, use the following buttons on the side panel. [M] (U) (Up Button): This button is used to move the cursor upwards. Use this button to select an item or adjust the parameters. [Ml (D) (Down Button): This button is used to move the cursor downwards. Use this button to select an item or adjust the parameters. CM] (R) (Right Button): This button is used to move the cursor to the right. Use this button to select or adjust the parameters of the selected item. The parameter changes each time this button is pressed. {Ml (L) (Left Button): This button is used to move the cursor to the left. Use this button to select or adjust the parameters of the selected item. The parameter changes each time this button Is pressed. (Mi (S) (Set Button): This button is used to set the determined parameter. If the item has its own setting menu (as indicated by 1), press this button to display the setting menu. • All Reset Operation All Reset allows you to reset all setup menu items to the factory settings if you are unsure about the correct settings. Proceed as follows: (1) Make sure that the CAM SET UP menu Is not displayed (a camera picture is displayed). (2) While pressing both mi (L) and mi (R), press [Mi (S) for a few seconds. The words ALL RESET momentarily appear on the monitor. At this time all adjustments and parameters are reset to the factory default settings. -12- Manual Level Adjustment Manual Mask Area Selection White Balance___ ATW j AWC Manual Mask Area Selection Manual Level Adjustment Chroma AP Gain Gain Pedestal Hue • Opening the Setup Menu Press and hold down [Ml (S) for a second or longer. c N ** CAM SET UP **__ CAMERA ZD OFF,"'! ALC/ELC ALC 1 SHUTTER --- AGC ON SYNC INT WHITE BAL ATW END SET UP DISABLE _—_/ The CAM SET UP menu appears on the monitor as shown above. : Check the current settings on the menu. Refer to the sections below for a detailed description of menu items, if you decide not to make any changes after checking the current settings, move the cursor to END at ] the start of the bottom line, and press tm] (S) to close the CAM SET UP menu and return to normal camera picture mode. Note: If no button is pressed for 6 minutes while the CAM SET UP menu or any other setting menu is displayed, displaying the menu is automatically canceled and the mode returns to the normal camera picture. \ ** CAM SET UP * * CAMERA ID OFF 1 ALC/ELC ALC SHUTTER --- AGC ON SYNC INT WHITE BAL ATW ^ END] ^ SET UP DISABLE • Editing the CAM SET UP Menu Important Notice: When the words SET UP DISABLE appear on the bottom line of the CAM SET UP menu, you cannot change the currently active settings. This is to prevent accidental changing of the settings. To edit the CAM SET UP menu (change settings), use mi (U) and mi (D) or mi (L) and mi (R) to move the cursor to SET UP DISABLE in the bottom line. Press [Ml (S). SET UP DISABLE changes to SET UP ENABLE. Move the cursor to END, then to the item(s) you want to change. • Editing the SPECIAL menu To edit the SPECIAL menu (change settings), proceed as for editing the CAM S...