Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
WV-Q112 PANASONIC CANADA INC. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 PANASONIC SALES COMPANY DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC. San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina, P.R. 00985 (809)750-4300 Panasonic Digital Communications & Security Company Unit of Matsushita Electric Corporation of America Security Systems Group Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094 Zone Office Eastern: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303 Central: 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205 Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840 2003 © Matsushita Electric Industrial Co., Ltd. All rights reserved. OPTIONAL HEATER UNIT ¦ Optional Heater Unit WV-CW3H . Introduction Installing this heater unit enables the camera to operate under in a low-temperature environment of –30°C (–22°F). The heater turns on automatically when the temperature inside the camera drops below +10°C (50°F) and turns off when it rises. A small fan inside the unit will minimize condensation on the surface of the dome cover caused by changes in ambient temperature unless temperatures change too rapidly. The fan will stop when there is no possibility of condensation. . Precautions • This product should be installed and connected by qualified service personnel or system installers. • Do not use the same 24 V AC power source supplying the power to the camera for the heater unit. Connect another 24 V AC power source to the heater unit. If the same power source is used, turning the heater on and off may disturb the camera images. • When servicing, pay attention to high temperature on the surface of the unit. Disconnect the harness and wait until it cools. • When you install the camera in a low-temperature location and start operating it, it may take time (around 30 minutes) for the inside of the camera to warm up. Cut power once then supply power again. . Installation 1. Open the dome cover. (See Disassembling the camera.) 2. Place the heater unit in the camera and fix it with the supplied screw. 3. Insert the harness into the heater unit connector of the camera. 4. Fold the desiccant pack in half, and attach it with adhesive tape to point "A" shown in the figure. Note: Attach the desiccant pack so that it does not block ventilation holes or hang over the top of the wall. 5. Attach the dome cover while paying attention not to pinch the harness cable. 6. Connect the heater power cable of the camera. (See Connection.) . Specifications Required power: 24 V AC, 60 Hz Power consumption: 12.1 W maximum Dimensions: 29 mm (H) x 83 mm (W) x 89.5 mm (D) [1-1/8” (H) x 3-1/4”(W) x 3-1/2”(D)] Weights: 45 g (0.1 lbs) . Accessories Fixing screw (M3 x 12) ...................................1 pc. Desiccant pack .............................................1.pc. Adhesive tape Point “A” (inside the wall) Supplied screw Harness Fold Adhesive tape Point “A” (inside the wall) Supplied screw Harness Fold Azimuth adjuster . Heater unit installation See OPTIONAL HEATER UNIT for details. ¦ Connections . Video Output Connection Connect the video output connector to the monitor or other system device with the procured coaxial cable. The maximum extensible length is shown in the table. . Power Connection . Wire Colors & Functions Camera power cable Heater power cable Type of RG-59/U RG-6/U RG-11/U RG-15/U coaxial cable (3C-2V) (5C-2V) (7C-2V) (10C-2V) Recommended (m) 250 500 600 800 maximum cable length (ft) 825 1 650 1 980 2 640 Wire Color 24 V AC 12 V DC Black 24 V AC (L) Positive White 24 V AC (N) Negative Green/Yellow Ground Not Used . Cable Length and Wire Gauge 24 V AC The recommended cable length and thickness are shown in the table for reference. The voltage supplied to the power terminals of the camera should be within 19.5 V AC and 28 V AC. 12 V DC Use the formula below to calculate the power cable and power supply. The voltage supplied to the power terminals of the camera should be within 10.5 V DC and 16 V DC. 10.5 V DC . VA . 2(R x I x L) . 16 V DC L : Cable length (m) (ft) R : Resistance of copper wire (./m) (./ft) VA : DC output voltage of power supply unit I : DC current consumption (A). See specifications. Copper wire size (AWG) Length of Cable (Approx.) #24 (0.22 mm2) 95 314 #22 (0.33 mm2) 150 495 #20 (0.52 mm2) 255 842 #18 (0.83 mm2) 425 1 403 Recommended wire gauge for 24 V AC line. Copper wire size (AWG) Resistance ./m Resistance ./ft #24 (0.22 mm2) 0.078 0.026 #22 (0.33 mm2) 0.050 0.017 #20 (0.52 mm2) 0.03 0.010 #18 (0.83 mm2) 0.018 0.006 Resistance of copper wire [at 20 °C (68 °F)] (m) (ft) Wire Color 24 V AC Red 24 V AC (L) White 24 V AC (N) Caution: • Be sure to connect the GND (grounding) lead of the camera and grounding terminal of the power supply when using a 24 V AC power source. Adhesive tape Point “A” (inside the wall) Supplied screw Harness Fold ¦ Image Adjustment You can manually adjust the pan/tilt/azim...