Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
(If a higher file number already exists on the memory card, the consecutive number will be assigned.) There will be no duplication of file numbers. This is useful for organizing images on a computer. Example: When you record 3 images. Using a Memory Card CAMERA PLAY (VCR) CARD CAMERA CARD PLAY 101 When you replace the memory card and record an image. CONTINUOUS RESET 101-0102 101-0103 101-0104 101 101-0101 101 101-0101 MENU ( 37) CARD SETUP FILE NOS.••••CONTINUOUS To change the setting, open the menu and select [CARD SETUP]. Select [FILE NOS.], set it to [RESET] and close the menu. 91 Recording Still Images on a Memory Card You can record still images with the camcorder, from a tape in the camcorder or from devices connected via the DV terminal or AV terminal. You can also record a still image on the memory card while you record a movie on the tape. CAMERA PLAY (VCR) CARD CAMERA CARD PLAY Card access indicator PHOTO button 1. Set the camcorder to CARD CAMERA mode. A white focusing frame appears in the center of the screen. The camcorder will focus on the subject in the center of the screen. To change the focusing point, see Selecting the Focusing Point ( 99). 2. Press the PHOTO button halfway. • and focusing frame turn green when focus is adjusted. The beep sounds twice. The picture may appear out of focus for a moment while the camcorder is focusing. • Exposure is locked. • When you press the PHOTO button on the wireless controller, recording starts immediately. 3. Press the PHOTO button fully. • and focusing frame disappear and you hear a shutter sound. • The card access indicator flashes and the card access display appears. • The still image shown on the screen will be recorded on the memory card. • Do not turn off the camcorder, change the position of the TAPE/CARD switch, disconnect the power source, open the memory card cover or remove the memory card while the card access indicator is flashing. Doing so could result in data damage. • When you are using a SD Memory Card, make sure that the protect switch is set to allow recording. • Connection to a computer or PictBridge compliant printer will not work when the memory card contains more than 1800 images. For best performance, we recommend not recording more than 100 images on the memory card when you plan to connect the camcorder to a computer or printer. E When you are using a Macintosh computer, you may not be able to download image with ImageBrowser or with OS standard software when the memory card contains more than 1000 images. In such case, use a PC card reader for downloading the images. • When the subject is too bright (overexposed), use the optional FS-28U ND filter. • When the Focus-Priority mode is set to [ON]: When you press the PHOTO button fully before and focusing frame turn green, it may take up to 2* seconds until focus is adjusted and the still image can be recorded to the memory card. * Up to 4 seconds in the Low Light and the night modes. If the subject is not suitable for autofocus, the focusing frame turns yellow and locks the focus. Adjust the focus manually with the SET dial. • When the Focus-Priority mode is set to [OFF]: No focusing frame appears. In step 2, turns green, and focus and exposure are locked. • The camcorder shuts off when you do not operate it for 5 minutes to save power. “ AUTO POWER OFF” appears 20 seconds before shutoff. To continue recording, turn the POWER switch to OFF and then back to CAMERA. Recording a Still Image on a Memory Card While Recording Movies on a Tape When you are recording a movie on a tape, you can record the same picture as a still image on the memory card. Select the image quality from normal or fine. CAMERA PLAY (VCR) CARD CAMERA CARD PLAY MENU CAMERA SETUP STILL I.REC••OFF ( 37) 1. Open the menu and select [CAMERA SETUP]. Select [STILL I.REC], set it to [ FINE] or [ NORMAL] and close the menu. 2. While you are recording a movie, press the PHOTO button. Using a Memory Card • The size of the still image will be 640 x 480. • The quality of the still image is slightly lower than a still image recorded in CARD CAMERA mode. • The still image cannot be recorded on a memory card when a fader, effect or the multi-image screen is activated. • The still image cannot be recorded on a memory card when the widescreen mode is selected. • “ ” appears when you press the PHOTO button when [STILL I.REC] is set to [OFF]. 93 Recording from a Tape in the Camcorder CAMERA PLAY (VCR) CARD CAMERA CARD PLAY 1. Play back the tape. 2. Press the PHOTO button halfway when the scene you wish to record appears. • The camcorder pauses playback. The remaining image capacity and other information appear. • When you press the PHOTO button on the wireless controller, recording starts immediately. 3. Press the PHOTO button fully. • The card access indicator flashes. • You can also record a still image by pressing the PHOTO button fully when the tape is in playback pause mode. Recording from Other Video Devices You can reco...
Otros modelos de este manual:Videocámaras - ZR200 (3.94 mb)