Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
If the problem still persists, disconnect all power sources (including the battery pack and the backup battery). This will reset all the camcorder’s settings. flashes on the screen. -Load a cassette ( 21). flashes on the screen. -Battery pack is exhausted. Replace or charge the battery pack ( 15). flashes on the screen. -Condensation is detected. Refer to Condensation ( 56). [REMOVE THE CASSETTE] appears on the screen. -Remove the cassette and reinsert it ( 21). Video noise appears on screen. -When using the camcorder in a room where a plasma TV is located, keep a distance between the camcorder and the plasma TV. Video noise appears on the TV screen. -When using the camcorder in a room where a TV is located, keep a distance between the compact power adapter and the power or antenna cables of the TV. The tape stops during record pause or playback pause. -To protect the tape and video heads, the camcorder will enter the stop mode ( ) if left in playback pause ( ) or record 50 • Additional Information pause ( ) mode for 4 minutes 30 seconds. To resume the operation press Start/Stop (when recording) or push the joystick ( ) toward / (during playback). Recording Image will not appear on the screen. -Set the camcorder to mode ( 23). [SET THE TIME ZONE, DATE AND TIME] appears on the screen. -Set the time zone, date and time ( 20). -Replace the backup lithium battery ( 17) and set the time zone, date and time. Pressing will not start recording. Start/Stop -Set the camcorder to mode ( 23). -Load a cassette ( 21). -Tape reached the end (“ END” appears on the screen). Rewind the tape or replace the cassette ( 21). -Cassette is protected ( flashes on the screen). Change the position of the protect switch ( 55). Camcorder will not focus. -Autofocus does not work on that subject. Focus manually ( 32). -If you are using the viewfinder, adjust it with the dioptric adjustment lever ( 23). -Lens is dirty. Clean the lens with a soft lens-cleaning cloth ( 56). Never use tissue paper to clean the lens. Sound is distorted. -When recording near loud sounds (such as fireworks or concerts), sound may become distorted. Viewfinder picture is blurred. -Adjust the viewfinder with the dioptric adjustment lever ( 23). Playback During playback there is video noise. -Video heads are dirty. Clean the video heads ( 2). Playback does not start. -Load a cassette ( 21). -Set the camcorder to mode ( 27). -Tape reached the end (“ END” appears on the screen). Rewind the tape ( 21). No sound from the built-in speaker. -Open the LCD panel. -Speaker volume is turned off. Adjust the volume with the [SPEAKER VOLUME] setting ( 27). Image will not appear on the TV screen. -Check again that the camcorder is properly connected to the TV ( 39). Tape is running, but image will not appear on the TV screen. -TV/VIDEO selector on the TV is not set to VIDEO. Set the selector to VIDEO ( 40). -Video heads are dirty. Clean the video heads ( 2). -You attempted to play back or dub a copyright protected tape ( 42). Stop playback/dubbing. Editing Cannot record with this camcorder video input from an external video device connected using a DV cable. -Wrong signal standard. Refer also to the instruction manual of the connected device. Additional Information • 51 List of Messages (in alphabetical order) CHANGE THE BATTERY PACK -Battery pack is exhausted. Replace or charge the battery pack ( 15). CHECK THE CASSETTE [INCORRECT TAPE SPECIFICATION] -You attempted to play back a tape recorded in HD (high definition) standard. CHECK THE INPUT -The DV cable is not correctly connected to the DV terminal ( 39), or the connected digital device is turned off. CONDENSATION HAS BEEN DETECTED -Condensation has been detected in the camcorder ( 56). CONDENSATION HAS BEEN DETECTED REMOVE THE CASSETTE -Condensation has been detected in the camcorder ( 56). Remove the cassette. COPYRIGHT PROTECTED DUBBING RESTRICTED -You attempted to dub a copyright protected tape ( 42). COPYRIGHT PROTECTED PLAYBACK IS RESTRICTED -You attempted to play back a copyright protected tape ( 42). HEADS DIRTY, USE CLEANING CASSETTE -Video heads are dirty. Clean the video heads ( 2). INCORRECT TAPE SPECIFICATION PLAYBACK IS RESTRICTED -You attempted to play back a tape recorded in a different television system (PAL or SECAM) or in a recording standard not supported by this camcorder. INPUT SIGNAL NOT SUPPORTED -The digital device connected with the DV cable is incompatible with the camcorder. REMOVE THE CASSETTE -Camcorder stopped operating to protect the tape. Remove the cassette and reinsert it ( 21). SET THE TIME ZONE, DATE AND TIME -You have not set the time zone, date and time. This message appears each time you turn the power on until you set the time zone, date and time ( 20). TAPE END -Tape reached the end. Rewind the tape or replace the cassette. THE TAPE IS SET FOR ERASURE PREVENTION -Cassette is protected. Replace the cassette or change the position of the protect switch ( 55). 52 • Additional Informatio...