Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Before Requesting Service (Problems & Solutions)
Power Supply
Normal Recording
Indicaitons
Playback (Sound)
P1:
The Movie Camera does not turn on.
P1:
Recording cannot be started even though
P1:
The Time Code becomes incorrect.
P1:
No sound is played back from the Movie
S1:
Is the Battery or the AC Adaptor connected
the Movie Camera is supplied with power
S1:
In the Slow Motion Playback Mode in
Camera’s built-in speaker or headphones.
correctly? Confirm the connection. (p. 8, 10)
and the cassette is inserted correctly.
reverse direction, the counter of the Time
S1:
Is the volume set too low? During playback,
P2:
The Movie Camera has turned off
S1-1: Is the erasure prevention slider of the
Code Indication may not be stable, however,
keep the [PUSH] Dial pressed until the
automatically.
cassette open? If it is open (set to [SAVE]),
this is not a malfunction.
[VOLUME] Indication appears. Then turn the
S2:
If you leave the Movie Camera in the
recording is not possible. (p. 13)
[PUSH] Dial to adjust the volume. (p. 39)
P2:
The Remaining Tape Time Indication
Recording Pause Mode for more than
S1-2: Has the tape reached its end? Insert a new
disappears.
P2:
Different sounds are played back
6 minutes, it automatically switches off to
cassette. (p. 12)
S2:
If you record a still picture in the Photoshot
together.
protect the tape and to conserve battery
S1-3: Is the Movie Camera turned on? (p. 26)
Mode, the Remaining Tape Time Indication
S2:
[12bit AUDIO] on the [PLAYBACK
power. (p. 27)
S1-4: Is the [CAMERA] Lamp lit? When the
may disappear temporarily. However, if you
FUNCTIONS] Sub-Menu of the [VCR
[CAMERA] Lamp is not lit, no recording
P3:
The Movie Camera quickly turns off.
switch the Movie Camera over to the Normal
FUNCTIONS] Main-Menu is set to [MIX].
functions can be operated. (p. 26)
S3-1: Is the Battery discharged? When the
Recording Mode, it appears again.
Therefore, the original sound and the sound
S1-5: Is the Condensation Indicaiton [3]
Remaining Battery Power Indication is flashing
dubbed with audio dubbing are played back
displayed? When condensation has formed,
P3:
The Remaining Tape Time Indication
or the [X] Indication is displayed, the
together. It is also possible to play them back
no functions except taking out the cassette
does not match the actual remaining tape
Battery is discharged. Charge the Battery or
individually. (p. 79)
can be operated. Wait until the
time.
attach a fully charged Battery. (p. 10, 122)
Condensation Indicaiton disappears.
S3-1: If scenes of less than 15 seconds are
P3:
The original sound was erased by
S3-2: Has condensation formed? If the Movie
(p. 116)
recorded successively, the remaining tape
performing audio dubbing.
Camera is brought from a cold to a warm place,
time is not indicated correctly.
S3:
If you perform audio dubbing on a recording
condensation may form inside. In this case, the
Other Recording
S3-2: The Remaining Tape Time Indication may
made in the [16bit] Mode (p. 78), the original
Movie Camera automatically switches off and
show a remaining tape time that is
sound is erased. If you want to keep the
no operation can be performed except taking
P1:
The picture on the LCD Monitor/in the
2–3 minutes shorter than the actual
original sound, be sure to select the [12bit]
out the cassette. Wait until the Condensation
Viewfinder suddenly stands still for a few
remaining tape time.
Mode for the original recording.
Indication disappears. (p. 116)
seconds.
P4:
No playback sound is reproduced.
P4:
Something is wrong with the Movie
S1:
Did you press the [PHOTO SHOT] Button? If
Playback (Picture)
S4-1: Is [12bit AUDIO] on the [PLAYBACK
Camera’s operation. Alternatively, the
you press the [PHOTO SHOT] Button, a still
FUNCTIONS] Sub-Menu of the [VCR
Movie Camera is turned on, however no
picture is recorded for approximately
P1:
No playback picture is reproduced when
FUNCTIONS] Main-Menu set to [ST2] even
functions operate.
7 seconds. After approximately 7 seconds,
pressing the Play Button [1].
though no audio dubbing has been
S4-1: Press the [RESET] Button on the Movie
the Movie Camera switches back to the
S1:
Is the [VCR] Lamp lit? When the [VCR]
performed on the cassette that you are
Camera with a pointed object. If this does
Recording Pause Mode. (p. 34)
Lamp is not lit, no playback functions can be
playing back? When you play back a
not solve the problem, first disconnect the
operated. (p. 38)
P2:
The Auto Focus Function does not work.
cassette onto which no audio dubbing was
power supply and wait for a minute or so,
S2-1: Is the Manual Focus Mode selected? If you
P2:
Mosaic-like patterns appear in the picture
performed, [12bit AUDIO] must be set to
and then reconnect the power supply to turn
select the Auto Focus Mode, the focus is
during Cue, Review or Slow Motion
[ST1]. (p. 79)
the power back on.
adjusted automatically. (p. 30)
Playback.
S4-2: Is the Variable Speed Search Function
(If the above operation is performed when
S2-2: Is the subject or recording situation suitable
S2:
This phenomenon is a characteristic of the
activated? Press the Play Button [1] to
the [ACCESS] Lamp of the Card Slot is
for the Auto Focus Mode? The Auto Focus
digital video system. This is not a
cancel the Variable Speed Search Function.
lighting for NV-MX5 and NV-MX7, the data
Function does not work correctly for some
malfunction.
(p. 39)
of the Card may be damaged.)
kinds of subjects and recording situations. In
S4-2: Are the DPOF setting contents being
P3:
The Movie Camera is correctly connected
this case, use the Manual Focus Mode to
checked? It may take a while to check the
to a TV, however no playback picture is
adjust the focus. (p. 30)
settings. Wait until the [ACCESS] Lamp
reproduced.
goes off. (NV-MX5, NV-MX7 only)
S3:
Did you select “Video Input” on the TV?
Editing
Carefully read the operating instructions for
Battery
your TV and select the channel that matches
P1:
Audio dubbing cannot be performed.
the input sockets used for connection.
P1:
The Battery discharges quickly.
S1-1: Is the erasure prevention slider of the
S1-1: Is the Battery fully charged? Charge it with
cassette open? If it is open (set to [SAVE]),
P4:
The playback picture is not reproduced
the AC Adaptor. (p. 10)
editing is not possible. (p. 13)
clearly.
S1-2: Are you using the Battery in a place where
S1-2: Are you trying to edit parts of the tape
S4:
Are the video heads on the Movie Camera
the temperature is very low? The ambient
recorded in the LP Mode? As the tracks
dirty? If the video heads are dirty, the picture
temperature greatly influences the Battery’s
recorded in the LP Mode are narrower than
cannot be played back clearly. (p. 28)
performance. Its operation time becomes
the heads, audio dubbing is not possible.
shorter in a cold place. (p. 116)
(p. 13, 78)
S1-3: Has the Battery reached the end of its service
Miscellaneous/
Care of Unit/Options
life? The service life of the Battery is limited. It
depends on the way the Battery is used,
however when the operation time even after
proper charging is too short for normal use, the
service life of the Battery has reached its end.
P2:
The Battery cannot be charged.
S2:
If the DC Input Lead is connected to the AC
Adaptor, charging is not possible.
Disconnect the DC Input Lead.
104
105
...Otros modelos de este manual:
Videocámaras - NVMX1EG (6.68 mb)
Videocámaras - NVMX3A (6.68 mb)
Videocámaras - NVMX3EN (6.68 mb)
Videocámaras - NVMX5B (6.68 mb)