Votos - , Puntuación media:
(
)
)
Fabricar: Gigabyte
Tamaño del archivo: 1.59 mb
Nombre del archivo:
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
For more information, please see you computer documentation. GV-NX55128DP Graphics Accelerator - 6 4. Locate the PCI Express x 16 slot. If necessary, remove the metal cover from this slot; then align your graphics card with the PCI Express x 16 slot, and press it in firmly until the card is fully seated. 5. Replace the screw to fasten the card in place, and replace the computer cover. 6. Plug the display cable into your card; then turn on the computer and monitor. If your graphics card came with a DVI-I connector, you can connect a flat panel display to the appropriate connector, as shown below... To TV or VCR To VGA Monitor To Flat Panel Display You are now ready to proceed with the installation of the graphics card driver. Please refer to next chapter for detailed instructions. English -7 - Hardware Installation EnglishEnglish 3. Software Installation In this manual, we assume that your CD-ROM Drive to be Drive D: The installation of Win® 2000 / Win® XP drivers is very simple. When you insert the driver CD into your CD-ROM drive, you can see the AUTORUN window (if it does not show up, run "D:\setup.exe"). Then you can follow the guides to setup your graphics card driver. (Please follow the subsection 3.1.3 "Driver installation" to install the driver for your graphics accelerator.) 3.1. Win® XP driver and utilities installation 3.1.1. Operating system requirement • When loading the graphics card drivers for the system, please make sure you have installed DirectX 9 or later version to your system. • If you install the graphics card drivers for the motherboard built on SIS or VIA chipsets, please install the appropriate driver program for that motherboard. Or please contact your motherboard nearest dealer for motherboard driver. GV-NX55128DP Graphics Accelerator - 8 3.1.2. DirectX installation Install Microsoft DirectX to enable 3D hardware acceleration support for Windows® 2000 or Windows® XP to achieve better 3D performance. • Note: For software MPEG support in Windows® 2000 or Windows® XP, you must install DirectX first. Step 1. When the autorun window showes up, click the "Install DirectX 9" item. Click the "Install DirectX 9" item. Step 2. Select the I accept the agreement check box and click the "Next" button. Step 3. Click the "Next" button again to begin DirectX 9 installation. English -9 -Software Installation Installing the components. English Step 4. Click "Finish" to restart computer. Then the DirectX 9 installation is completed. GV-NX55128DP Graphics Accelerator - 10 3.1.3. Driver installation A. New hardware found After the graphics card is inserted into your computer at the first time, the windows will automatically detect a new hardware in the system and pop out a "New Hardware Found" message. The following is the step-by-step installation guide. Step 1: Found new hardware wizard: Video controller (VGA Compatible) Click the "Next" button to install the driver. (There is a driver CD disk that came with your graphics accelerator, please insert it now.) Or click the "Cancel" button to install the driver from AUTORUN window. Step 2: Found new hardware wizard: Searching and installing The wizard will search for the driver and install it automatically. Step 3: Found new hardware wizard: Finish Click the "Finish" button to finish the installation. English -11 -Software Installation EnglishEnglish B. Driver installation (Autorun Window) Insert the driver CD disk into your CD-ROM, and then you can see the AUTORUN window. If it does not show up, please run "D:\setup.exe". Step 1. When autorun window show up, click Install Display Driver item. Click the "Install Display Driver" item. Step 2. Click the "Next" button. Windows installs the driver components. Step 3. Click the "Finish" button and restart computer. Then the driver installation is completed. GV-NX55128DP Graphics Accelerator - 12 3.1.4. Utilities on driver CD Insert the driver CD disk into your CD-ROM, and then you can see the AUTORUN window. If it does not show up, please run "D:\setup.exe". • Install V-Tuner 2: Step 2.Click the "GIGABYTE Utility" item. Step 1.Click the "Utilities" item. Step 3. Click the "Next" button. Step 4. Enter your name and company. Step 5. Click the "Finish" button and restart computer. Then the V-Tuner 2 installation is completed. English -13 -Software Installation EnglishEnglish V-Tuner 2 V-Tuner 2 lets you adjust the working frequency of the graphic engine and video memory (Core Clock and Memory Clock). Displays core clock status Displays memory clock status Core speed Core speed adjustment adjustment Enables auto adjustment of core/ memory clock settings set by user when running 3D applications. Opens Help page Select choice of skin GV-NX55128DP Graphics Accelerator - 14 3.1.5. Taskbar icon After installation of the display drivers, you will find a GBT icon on the taskbar's status area. Right-click this icon to open the GBT control panel, showing a menu composed of shortcut of the graphics card's enhanced and oth...