Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have the g symbol near the remote sensor, this remote commander will not operate the TV. Remote sensor ...........\ S3 111 - l|| E3 1 □ || || Hä 0^4 1 ® pO OOQ © a I TV I / I VIDEO I To operate Set I TV I / I VIDEOI to the VCR I VIDEO I and point at the remote sensor on the VCR a Sony TV TV I and point at the remote sensor on the TV Notes • The TV/VIDEO button selects an input source of the TV from either aerial in or line in. The button does not control this VCR. • With normal use, the batteries should last about three to six months. • If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage. • Do not use a new battery with an old one. • Do not use different types of batteries. Getting Started 5 Getting Started Step 3 Connecting the VCR Connect the aerial to your VCR and TV as shown below to watch TV programmes and VCR pictures on your TV. In addition, if your TV has audio/video (A/V) input jacks, we recommend you connect the VCR to your TV using an audio/video cable to get a better picture and sound. 1 Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR. Vv% AERIAL N 0"®-1 ©OUT W 2 Connect AERIAL OUT of the VCR and the aerial input of your TV using the supplied aerial cable. AERIAL ©IN Q^dDmm—шшош H 3 Connect the mains lead to the mains. Additional connections To a TV that has audio/video input jacks This additional connection improves picture and sound quality. Connect the TV as shown on the right. If you want to use the Trinitron TV Synchro Play function (see page 21), this connection is necessary. (If your TV has two or more inputs, connect the audio/video cable to the VIDEO IN 1 jacks.) Getting Started LINE OUT LINE IN -1- Audio/video cable (not supplied) 6 Step 4 Tuning your TV to the VCR If you have connected your VCR to the TV using the audio/video cable, skip this step. i/u oN/STANDby 1 ON/STANDBY i/c!) | Press 1/U ON/STANDBY to turn on the VCR. 2 RF CHANNEL Press RF CHANNEL on the VCR. The factory-preset RF channel appears in the display window. The VCR signal is output through this channel to the TV. SP APC O r ~l ~l hi _/ /_ 3 4 RF CHANNEL Turn on your TV and select a programme position for the VCR picture. This channel will now be referred to as the video channel. Some TV has the programme position, such as 0, that is reserved for a VCR. In this case, select that programme position for the VCR picture. Refer to the instruction manual of your TV for details. Press RF CHANNEL. The TV system indicator appears in the display window. Press PROGRAM +/- to select the correct TV system. - PROGRAM + If your TV system is Select B/G G I I D/K K Selected TV system SP APC n I I ~l r m r j c /_'/ continued Getting Started 7 Getting Started Step 4: Tuning your TV to the VCR (continued) 5 Tune the TV to the same channel as that shown in the display window so that the picture on the right appears on the TV screen. Refer to your TV manual for tuning instructions. If the picture does not appear clearly, see “To obtain a clear picture from the VCR” below. 6 RF CHANNEL Press RF CHANNEL. You have now tuned your TV to the VCR. From now on, whenever you want to play a tape, set the TV to the video channel. To obtain a clear picture from the VCR If the picture does not appear clearly in step 5 above, go to step 6 to finish this procedure once. Then start from step 2. After pressing RF CHANNEL in step 2 to display the RF channel, press PROGRAM +/- so that another RF channel appears. Then tune the TV to the new RF channel until a clear picture appears. If you cannot obtain a clear picture after performing this procedure, we recommend you connect the VCR and TV using an audio/video cable (see “To a TV that has audio/video input jacks” on page 6). If the same symptom persists, consult your nearest Sony dealer. Note • If you set the wrong TV system, you may have no sound or sound may be distorted (noisy sound). 8 Getting Started Step 5 Selecting a language You can change the on-screen display language from English to Arabic. Before you start... • Turn on your TV and set it to the video channel. CD © CD CD CD 0 ©1 U © o cd ■ O CD CD cd GD CD O on/standby menu OK >/. 1 [STANDBY) o Press ON/STANDBY to turn on the VCR. 2 • MENU * _ /-\ Press MENU, then press >/. to move the cursor (►) to LANGUAGE and press OK. 3 Press to select the desired language, then press OK. LANGUAGE /iiJ ENGLISH [♦♦] jl M >1 [ OK ] Uji Getting Started 9 Getting Started Step 6 Presetting channels First, we recommend that you preset the receivable channels in your area using the one touch tuning or the AUTO PRESET in the TUNER PRESET menu. Then, if some channel...