Votos - 2, Puntuación media: 3.5 ( )

Fabricar: Sony Tamaño del archivo: 845.6 kb Nombre del archivo: Idioma del manual:

2 Insert a tape. The VCR turns on and starts playing automatically if you insert a tape with its safety tab removed. continued Basic Operations 19 Playing a tape (continued) PLAY OK 3 Press H PLAY. When the tape reaches the end, it will rewind automatically. Additional tasks To Press Stop play x STOP Pause play X PAUSE Resume play after pause X PAUSE or H PLAY Fast-forward the tape M # FF during stop Rewind the tape m 3 REW during stop Eject the tape Z EJECT To set the colour system If streaks appear during playback, press COLOR SYSTEM on the VCR to conform to the system that the tape was recorded in. (Normally, the colour system is correctly set whenever the tape is inserted.) If your tape was Press COLOR SYSTEM until the indication below recorded in appears in the display window. PAL PAL MESECAM PAL NTSC NTSC To play an NTSC-recorded tape Set NTSC PB in the SET UP MENU according to the colour system of your TV. For details, see page 47. If your TV is Set NTSC PB to PAL ON PAL TV NTSC 4.43 4.43 NTSC 3.58 3.58 Basic Operations To use the time counter At the point on the tape that you want to find later, press CLEAR. The counter in the display window resets to “0:00:00.” Search for the point afterwards by referring to the counter. SP APC To display the counter on the TV screen, press DISPLAY. Notes • When you play back a tape recorded in the PAL or MESECAM colour system, streaks may appear even if the colour system setting is set to AUTO. If so, select the colour system, PAL or MESECAM in the PAL/MESECAM option of the SET UP MENU (see page 47 for details). • The counter resets to “0:00:00” whenever a tape is reinserted. • The counter stops counting when it comes to a portion with no recording. • If a tape has portions recorded in both PAL and NTSC systems, the time counter reading will not be correct. This is due to the difference between the counting cycles of the two colour systems. • Depending on your TV, the following may occur while playing an NTSC-recorded tape: – the picture is black and white – the picture shakes – no picture appears on the TV screen – black streaks appear horizontally on the TV screen – the colour density increases or decreases. • Tapes recorded in the LP mode of NTSC system on other VCRs can be played back on this VCR, but the picture quality cannot be guaranteed. • While setting the menu on the TV screen, you cannot use the H PLAY, X PAUSE, M # FF, m 3 REW or x STOP button. These buttons are used for menu operations. Basic Operations continued Basic Operations Playing a tape (continued) Turning on the VCR and TV, and starting playback automatically (Trinitron TV Synchro Play) You can only use this function if your TV is made by Sony (Trinitron TV). How to connect to use this function Connect the VCR and TV with the audio/video cable (see “To a TV that has audio/video input jacks” on page 7). Be sure to connect the audio/video cable to the VIDEO IN 1 jacks on the TV if the TV has two inputs or more. The TV must be placed where it will respond to the remote commander while you are pointing it at the VCR. Operation Make sure that the TV’s main power is on. Press TRINITRON TV SYNCHRO PLAY and hold the remote commander in place for about two seconds. The VCR and TV turn on, and the TV is set to VCR reception. If there is a tape in the VCR, playback starts automatically. Notes • If the Trinitron TV Synchro Play function does not work properly: – Wait a few moments, and press the button again. – Replace both of the batteries with new ones, and press the button again. Note that this function may not operate some Sony TVs because of the remote commander’s signal limitations. • Do not press TRINITRON TV SYNCHRO PLAY while playing back a video tape. If you do so, the TV’s input source will momentarily switch to the TV’s tuner. Basic Operations Recording TV programmes 1 2 3 4 5 6 7 8 9 0 DISPLAY z REC PROG +/– SP/LP (SP/EP) INPUT SELECT Basic Operations Turn on your TV and set it to the video channel. Insert a tape with its safety tab in place. PROG Press PROG +/– to select the programme position you want to record. SP APC continued Basic Operations Recording TV programmes (continued) 4 SP/LP Press SP/LP (SP/EP) to select the tape speed, SP or LP. LP (Long Play) provides recording time twice as long as SP (Standard Play), however, SP produces better picture and audio quality. (SP/EP) LP APC 5 REC Press z REC to start recording. The recording indicator lights up red in the display window. LP APCRecording indicator To stop recording Press x STOP. To check the remaining tape length Press DISPLAY. The white bar indicates the approximate length of tape remaining. S E– 0 00 Remaining tape length Time counter To watch another TV programme while recording 1 If the TV is connected to the VCR using an audio/video cable, set the TV to TV input. If the TV is connected to the VCR using only the aerial cable, skip this step. 2 Select another programme position on the TV. To save a recording To prevent acci...

Descargar ahora

Introduzca dos números de la imagen: