Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
If the sounder does not sound, CALL FOR SERVICE IMMEDIATELY. 4. Fault zones. Open each protected door and window in turn and listen for three beeps from the keypad. Identification of each faulted protection point should appear on the display. The display will clear when the door or window is closed. - 32 Testing the System (cont'd) 5. + 1 (Security Code) OFF Walk in front of any interior motion detectors (if used) and listen for three beeps. The keypad should display the identification of the detector when the detector is activated. The display will clear when no motion is detected. Note that if you are using wireless motion detectors, there is a 3-minute delay between activations. This is to conserve battery life. To test all smoke detectors, follow the manufacturer's instructions. The keypad should display the identification of each detector when each is activated. If you experience a problem with any protection point (no confirming sounds, no display), CALL FOR SERVICE IMMEDIATELY. When you have checked (and closed, where necessary) all protection points, no zone identification numbers should be displayed on the keypad. When you complete testing, exit the TEST mode by continuing with step 5. Exit TEST mode. Enter your security code and press the OFF key. If you inadvertently leave the test mode active, it automatically turns off after approximately 4 hours. - 33 Trouble Conditions Typical Check Displays The word CHECK on the keypad's display, accompanied by a rapid beeping at the keypad, indicates a trouble condition in the system. The displays in parentheses in the left column below may appear on non-alpha keypads when the associated trouble condition is present. To silence the beeping sound for “check” conditions, press any key. CHECK + Zone Indicates that a problem exists with those Descriptors zone(s)*. First, determine why the zone(s) displayed are faulted (open window or door; open or shorted zone terminals; etc.) and correct the problem. If the zone(s) contain a wireless detector, check that changes in the room (moving furniture, televisions, etc.) are not blocking wireless signals to/from the detector. If the problem has been corrected, the zone descriptor(s) and CHECK should disappear from the keypad display. If not, key an OFF sequence (enter the 4-digit security code, then press the OFF key) to clear the display. A “Check” condition can also indicate a wiring problem (opens or shorts, for instance). If the CHECK display persists, CALL FOR SERVICE IMMEDIATELY. Note that the system will not allow arming if a “Check” condition exists. To arm the system with a “Check” condition present, you must first bypass the zone(s) having the “Check” condition. NOTE: Zone 9 represents a problem with wireless receivers or other system devices, which are not user-serviceable. CALL FOR SERVICE IMMEDIATELY. - 34 Telco Fault (or CHECK and zone 94) Telco Fault (or CHECK and zone 94) SYSTEM LO BAT (or BAT with no zone no.) Trouble Conditions (cont'd) If the telephone line monitor feature has been programmed for your system, this display indicates that the telephone line has been disconnected or cut. In some systems, this display is accompanied by a trouble sound from the keypad and an external sounder. CONTACT YOUR SERVICE COMPANY IMMEDIATELY. To silence the trouble sound, enter your security code plus OFF. Indicates that a failure has occurred in the telephone communication portion of your system. CALL FOR SERVICE IMMEDIATELY. Indicates that a low system battery condition exists, and is accompanied by a once-perminute beeping* at the keypad. CALL FOR SERVICE IMMEDIATELY. *You can stop the beeping that accompanies a low- battery display by entering an OFF sequence (security code + OFF). LO BAT + zone descriptor (or BAT with zone no.) Indicates that a low-battery condition exists in the wireless transmitter** displayed, and is accompanied by a once-per-minute beeping at the keypad. CALL FOR SERVICE IMMEDIATELY. ** Not all systems use wireless transmitters. MODEM COMM Indicates that the control is on-line with the (or CC) central station's remote computer. The control will not operate while on-line. Wait a few minutes. The display should disappear. - 35 Trouble Conditions (cont’d) POWER indicator (if present) is off. AC LOSS is displayed. The system is operating on battery power only. If only some lights are out on the premises, check circuit breakers and fuses and reset or replace as necessary. CALL FOR SERVICE IMMEDIATELY if AC power cannot be restored to the system. Busy-Standby (or dI) If this remains displayed for more than 1 minute, system is disabled. CALL FOR SERVICE AT ONCE. OPEN CIRCUIT (or OC) The keypad is not receiving signals from the control. CALL FOR SERVICE AT ONCE. Long Rng Trbl (or bF) If programmed, backup Long Range Radio communication has failed. CALL FOR SERVICE AT ONCE. Bell failure (or CHECK 70) Bell/Siren supervision failure. CALL FOR SERVICE AT ONCE. RF Jam (or Check 90) If enabled and a Rec...
Otros modelos de este manual:Vídeo - Security System VISTA-15 (201.73 kb)