Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
The holder accepts a 1/ 4-inch striped stranded wire. Tighten the fuse holder ends by securely tightening by hand. *Improper connection could result in numerous “Start up test” notifications, and increased usage on monthly billing. Powering the Unit for the First Time *Disconnect the backup battery if it is installed. Connect the two coax cables from the combo antenna (securely) and connect the vehicle’s 12-volt power and observe the LED on the Module. During the initial 15 minutes after +12 volts is connected to the Module, the LED should flash green at the rate of 1 second “on”, 5 seconds “off”, this feature is designed for installation test purposes (15 minute Start-Up). 6 INSTALLATION INSTALLATION Within five minutes the flash rate will change to approximately one second on and one second off to indicate that the GPS Receiver has established a location “lock”. Within 1 minute the flash color should be green to indicate good cellular coverage. If you do not get the results above, refer to page 13, Section 13 – Troubleshooting Confirming Proper Operation The Test wire (see wiring diagram) on the TRAKNET is for testing the internal functionality of the hardware. Running tests with this wire grounded will not send data to the call center. The user account does not need to be activated to run the tests. Grounding the wire will start test mode function. If the wire is not removed from ground the unit will remain in the test mode for 5 minutes and then return to normal operation. To start the tests again you must ground the test wire again. If you want the TRAKNET to function normally after testing, remove the test wire from ground and tape the end to prevent the device from going into test mode during normal operation. Remember that the TRAKNET will remain in the test mode for only 5 minutes at a time and you will need to cycle the test wire to re-enter the test mode. The TRAKNET interface circuits are all pre-wired in the cable harness. Table 1 also shows the wire colors associated with the input and output circuits. The digital outputs are provided to switch optional external devices. Each can sink 1 amp at 35 volts. The outputs are voltage protected so they can sink current from inductive loads. If the individual sink current is allowed to exceed 1 amp, the outputs could be damaged. The digital inputs are triggered by a contact closure or short of less than 100 ohms from the contact to ground on their inputs. 7 LED STATUS INDICATOR LED STATUS INDICATOR LED Status Indicator BI-COLOR ON BOARD LED: This unit has a bi-colored LED on unit. SOLID LED COLOR: Solid Green – Device is in Test Mode: no inputs are currently being triggered. Solid Orange – Device is in Test Mode: At least one input is currently being triggered. Solid Red – Device is in set up mode BLINKING LED COLOR: Blinking Green – Microburst and Cellular Service are available. Blinking Orange – Cellular Service, but not Microburst Service is available. Blinking Red – Neither Cellular Service nor Microburst service is available. BLINKING LED TIMING: OFF FOR 1 SECOND GPS Module is powered and signal is Valid, Cell Module is powered. OFF FOR 5 SECONDS GPS Module is powered and signal is invalid, cell module is powered. OFF FOR 10 SECONDS GPS module is turned off, Cell module is powered. OFF FOR 21 SECONDS GPS module is powered and signal is invalid, cell module is turned off. OFF FOR 25 SECONDS GPS module is powered and signal is invalid, Cell module is turned off. OFF FOR 30 SECONDS GPS module is turned off, Cell module is turned off. NOTE: It is highly recommended to perform a location request and other optional features before releasing the vehicle. 8 WIRING WIRING NOTE: Some Options Need to Be Pre-programmed From Crimestopper prior to installing the unit. Pin 1 Black: Chassis Ground Input THIS WIRE MUST BE CONNECTED TO THE CHASSIS METAL OF THE VEHICLE. Scrape away any paint or dirt to ensure a good connection. Pin 2 Green: Starter Disable (-) (Output #2) Requires Relay This wire has a negative output to hook up to optional relay. See wiring diagram for connection. Pin 3 Blue: GEO Fence (Optional) (-) Input #2 Connect wire to momentary switch 2 sec input to trigger for GEO fence or 15 sec input to trigger alarm. Pin 4: Empty Pin 5 Red: Battery Back Up Power (Input) Pre-wired to connector for battery back up. Pin 6 White: Overheat Trigger/ Road Side Assistance (-) Input #3 This wire needs 2 minute trigger for Overheat or 2 sec trigger for Road Side Assistance. Pre-programmed for Overheat. Pin 7: Empty Pin 8 Brown: Ignition Input #4 (+) This wire must be connected to an Ignition source. Pin 9: Empty Pin 10 Purple: LED (Optional) (+) Output This wire connects to optional LED for visual status of RSA or GEO Fence. Pin 11 Yellow: Door Unlock Output (-) This wire connects to the door unlock circuit. This wire is a negative output and may require additional relays to interface with different door lock circuits 9 WIRING WIRING Pin 12 Orange: Alarm Trigger (...
Otros modelos de este manual:Vídeo - TN-4004 (352.65 kb)