Votos - 3, Puntuación media: 4 ( )

Fabricar: Crimestopper Security Products Tamaño del archivo: 356 kb Nombre del archivo: Idioma del manual:

• In warm weather when your vehicle may start very quickly, “Timed Crank” mode may tend to over-crank the starter. • The only way to possibly correct the above issues is to go to the Option #21 and adjust the cranking time. When in “Timed Crank” mode, the cranking time can only be adjusted manually through option #21. When using Ultra-Smart Tachless or Regular Tach modes, cranking time is adjusted automatically. 18 DIESEL GLOW PLUG DELAY DIESEL GLOW PLUG DELAY This feature provides a solution for diesel vehicles without having to connect to the Glow Plug-“Wait to Start Circuit” input. This may be due to a variety of reasons for example: If your vehicle does not have a viable “Wait to Start Circuit” or you cannot locate and identify the circuit. You can choose from a selection of “pre-cranking” delay times. Once this mode is activated, the system will NO LONGER monitor the PINK glow plug input wire and will use a delay setting chosen by the installer in the option chart. NOTES: This feature is OFF by default and must be programmed before use. Once this feature is turned ON, the Pink Glow plug input wire is not used. The Remote start unit will always wait the programmed time before cranking EVEN IF the glow plugs warm up first. There are 3 different Delay times available for use: 10, 20, or 30 seconds. SEE PROGRAMMING OPTION CHART, next section. HOW TO USE THIS FEATURE: 1. See the “Programmable Options” next section and change Option #22 from "Monitor Glow Plug Light" to one of the delayed time values. (Default setting is to always monitor the PINK Glow Plug input wire.) 2. Once this option has changed the system will wait for the selected time before cranking the engine. PROGRAMMABLE OPTIONS You can program multiple options in one session if you start with the lowest option and continue on to higher options [if needed] without repeating steps #1-3 below. For example, you can follow the programming steps to change Option #2 to “OFF” by pressing the lock button on the remote, then you can continue pressing the program button additional times to get to a high number option and change the setting without having to repeat Steps 1-5. You can only go from low to higher option numbers in one session. To Engage Option Programming: 1. Open Hood (ground blue wire if no hood pin switch is installed) 2. Turn Key to the ON position 3. Press program / valet button 5 times, after a few seconds the unit will flash the lights 5 times. 4. Push the valet/program button [again] the number of times that corresponds to the option number desired (1 thru 30). You must get a light flash after each button press. See chart on next page for option list. 5. When you reach the desired programming level, Press button #1, #2 #3 or #4 to change the option. 6. Turn Ignition OFF, Close hood and check for changed features. Change each option individually repeating #1-5. 19 OPTION PROGRAMMING TABLE Option # 1 Option Description Engine Monitoring TX Button #1 Learn Tach TX Button #2 *Tachless* TX Button #3 TX Button #4 2 3 4 Auto lock with Ignition Passive Arming With Ignition or Last Door Active Re-Arm OFF Ignition and last door ON ON *ON* *OFF* *OFF* Ignition only *Last Door* only 5 Passive Locks ON *OFF* 6 7 8 9 Parking Lights on w/Disarm Dataport Protocol 1-Way = OFA, 2-Way = SL Double button press for Remote Starter and Trunk Release Siren Chirps on Remote Start OFF 1-Way ON OFF *ON* *2-Way* *OFF* *ON* 10 Disarm on Trunk pop OFF *ON* 11 Open Door Warning 5 Sec. *60 Sec.* 12 Door Lock Pulse Time 3 Sec. *0.5 Sec.* 13 Double Unlock Pulse 2 Pulses *1 Pulse* 14 Lock After Remote Start/Abort OFF *ON* 15 NOT USED N/A N/A 16 Timed Crank or Tach Monitor Pre-Set *Tach Monitor* 17 Blue/Black Wire Function AUX #2 *(-) Run / Ignition* 18 Siren Chirps with Arm/Disarm OFF *ON* 19 “Wake Up" pulse on Unlock (1-sec. +12V to IGN) ON *OFF* 20 20 OPTION PROGRAMMING TABLE 21 Starter Cranking Time (Option #16 is set to Timed Crank) PINK Wire function 0.75 Sec. Carjack *0.5 Sec.* *Glow Plug* 1.0 Sec. 1.5 Sec. 22 Diesel Glow Plug Delay 10 Seconds *Monitor Glow Plug 20 Seconds 30 Seconds 23 24 Remote Start Engine Run Time Smart Tachless Voltage Adjustment 12 Minutes -1% *24 Minutes* 1% 36 Minutes *Set to 93% for 48 Minutes 25 Horn Pulse 79-100% Pulse With Trigger (No Chirps) No Warn-A-Way *All Functions* default* 26 27 Aux # 3 Aux # 3 Time : 1 to 255 sec. Steady Momentary -1 Second *Momentary* +1 Second Timed *Default 12 Sec.* Latch On/Off 28 29 30 Aux # 4 Aux # 4 Time : 1 to 255 sec. Reset Options to default (*) Steady Momentary -1 Second *Momentary* +1 Second *Reset All Options* Timed *Default 12 Sec.* Latch On/Off PROGRAMMABLE OPTION DESCRIPTIONS: 1. ENGINE MONITORING: This option sets how the unit monitors your engine. You can program either for Tach mode in which the unit uses a Tach signal (RPM) or for “Ultra-Smart” Tachless mode that monitors voltage level. See pages 15-16 for more information and additional steps for actual Tach learning and Tach finder modes...

Descargar ahora

Introduzca dos números de la imagen: