Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Executing a macro 1. Press the MACRO button on Remote Control unit. 2. Within 3 seconds, press the MUSIC (MACRO1), MOVIE (MACRO2) or TV (MACRO3) button. The registered macro will be executed. After macro execution, the LCD display returns to the previous condition. Using Receiver 53 Using Receiver Using Receiver Using Remote Control Unit in Multiple Zones Using Remote Control Unit in Multiple Zones The VR-5700/VR-5090/VR-5080 offers dual-zone output and control, which enables you to use a single receiver to control devices and speakers for 2 zones. Due to its advanced features and controls, you can listen to music in one zone while a movie plays in the other! Depending on your tastes and budget, you can set up one of the following “sound scenarios” to make full use of the VR-5700/VR-5090/VR-5080’s capabilities: No additional amplifier for Zone B: You can use your receiver’s Speaker B output for Zone B. This allows you to listen to full surround sound in Zone A only, or in stereo in Zone A when Zone B is active. The sound in Zone B will always be in stereo. Stereo amplifier for Zone B: You use an additional stereo amplifier for Zone B (connected to the receiver’s Second Zone Preouts). This allows you to hear full surround sound in Zone A even if you are also listening in Zone B. The sound in Zone B will always be in stereo. This section covers only multiple-zone operation of the receiver. See Chapter Two for general operating instructions. How Do I Switch Control Modes? You can use Remote Control unit to operate your receiver and source devices from 2 different zones. To do so, you need to switch control modes to control the devices from each zone. To make operations from Zone B easier, we recommend that you purchase a second Remote Control unit. That way you can leave one Remote Control unit in Zone A that is always set up for Zone A operation, and another Remote Control unit in Zone B that is always set up for Zone B operation. Some system control features are not available when the Remote control unit is set up for multi-zone control. 54 Using Remote Control Unit in Multiple Zones To switch control modes for Zone A or Zone B: 1. Press the F. SHIFT = 11 (MULTI ZONE)* button on Remote Control unit. Menu1 2 3 4 5 6 7 8 9 10 +10 0 +100 /8 /7 1 1 Multi Zone On Each time the F. SHIFT =11 (MULTI ZONE)* button is pressed, switches the On and Off. Operating Devices in Zone B 1. Press the F. SHIFT =12 (ZONE A/B)* button on Remote Control unit. 1 2 3 4 5 6 7 8 9 10 11 +10 0 +100 /8 /7 1 1 Zone B Menu Each time the F. SHIFT = 12 (ZONE A/B)* button is pressed, switches Zone A and Zone B. Devices connected via digital jacks only cannot be listened to in Zone B. We recommend that you connect the analog jacks of all devices. You must use the composite video connections. Only video sources connected with composite connectors can be viewed in the second zone. * When an operation is described as [F.SHIFT = 11 (MULTI ZONE) button], for example, press the F.SHIFT button and press the next button (the 11 (MULTI ZONE) button in this case) within 8 seconds. 55 Using Receiver Using Remote Control Unit in Multiple Zones Using Receiver Operation using the SYS.POWER button on Remote Control unit To perform the Multi-Zone operation, switch the Multi Zone function On in advance (see page 55). 1. When the receiver is OFF (STANDBY mode): • To output the video and audio to Zone A, set the Zone setting of the remote to Zone A then press the SYS.POWER button on the remote. • To output the video and audio to Zone B, set the Zone setting of the remote to Zone B then press the SYS.POWER button on the remote. 2. When the video and audio are output to Zone A only: • To turn the receiver OFF (STANDBY mode), set the Zone setting of the remote to Zone A then press the SYS.POWER button on the remote. • To output the video and audio to Zone B, set the Zone setting of the remote to Zone B then press the SYS.POWER button on the remote. 3. When the video and audio are output to Zone B only: • To turn the receiver OFF (STANDBY mode), set the Zone setting of the remote to Zone B then press the SYS.POWER button on the remote. • To output the video and audio to Zone A, set the Zone setting of the remote to Zone A then press the SYS.POWER button on the remote. 4. When the video and audio are output to both Zone A and Zone B: • To turn the receiver OFF (STANDBY mode), set the Zone setting of the remote to Zone A then press the SYS.POWER button on the remote. • To defeat the video and audio outputs to Zone B, set the Zone setting of the remote to Zone B then press the SYS.POWER button on the remote. The receiver can also be turned OFF (STANDBY mode) by pressing the POWER button on the receiver. 56 Chapter Three: Button Layout in Controlling Other Devices The remote control unit provided with the receiver can also control a variety of AV devices. As the functions of the buttons are variable depending on the controlled device, it is recommended to control each ...
Otros modelos de este manual:Vídeo - VR-5090 (918.25 kb)
Vídeo - VR-5080 (918.25 kb)