Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Otherwise, it can cause trouble. • Be sure to switch power off before installing the pan/tilt head. • Secure enough space around the pan/tilt head and camera housing so there will be no obstacles in their operating range. • When checking the pan/tilt head for operation and when actually operating it, make sure that there is no one in its operating range. 0- ■ Installation Procedures • Fasten the pan/tilt head securely using the four mounting holes. • Install the pan/tilt head on a base so that the head will be high enough from the floor to prevent problems resulting with the cables from the housing rubbing with the floor, -1 ■ Installing Video Relay Box • The maximum cable extension distance from the pan/tilt head to the control panel, monitor, etc. is 500 m. But the optional cables for pan/tilt head control and video camera control are 10 m, 20 m and 30 m long, respectively. In cases where cable extension is necessary, install the supplied video relay box at a point within the optional cable length, and connect the optional cable in the relay box to coaxial cables (5C-2V or equivalent) and 10 BASE-T cable, for example. (For details, refer to the section CONNECTION. (D Fasten the pole mounting plate and the belt (to be locally purchased) on the back of the video relay box with the four bolts (supplied). Pole mounting plate (D Fasten the video relay box to the pole using the pole mounting plate and the belt. Unit: mm (inch) (D Pass the cables through the rubber bushing at the bottom of the video relay box, and pull out the spiral holder. The cables are fastened in place. Connect and clamp the cables in the video relay box as shown in the figure. From pan/tilt head —# To control panel, monitor, etc. -12- ■ Mounting the Tilting Arm • Mount the tilting arm (an accessory) with the eight tilting arm screws (accessories). • Tighten the screws securely so they won't become loose while the arm is in use. ■ Setting the Cable Compensation Circuit The maximum cable length from the pan/tilt head to the controller is 500 m (in case of a 5C-2V cable), including the length of the video camera control cable. If cable length is over 300 m, take the following steps to set the cable compensation circuit to ON. © Remove the six screws from the front panel of the base, and pull out the panel toward yourself. Do not remove the two screws in the center of the panel. (D Set the switch on the printed circuit board at the rear side of the panel to ON. (D Place the panel back on and tighten the screws. (Mount the panel securely to prevent rainwater, etc. from getting inside.) JL Cable compensation circuit board Remove screws. (6 pcs.) OFF —f —7i ö-B4-] Front panel / /1 Do not remove these screws. Set this switch ON. ■ Mounting the Housing • With the tilting arm held horizontal, fit the temporary mounting boss on the bottom of the housing into the groove in the arm, and temporarily fasten the housing from below with the two housing mounting bolts. • Move the camera housing back and forth till it is well balanced, then fasten it securely. As the stop position depends heavily on the balance of the camera housing, be sure to check the accuracy of the preset stop positions after tilting with the picture from the camera. • Rough Yardstick for Good Balance (±5' from preset stop position) The position of good balance varies depending on the combination of the camera and lenses. Set the arm scale in line with the housing position mark (|), referring to the table below. Camera Lens Housing Position AW-E300 AW-E600 AW-E600 AW-E600 AW-E800 AW-E800 AW-LZ14MD55 AW-S14XBMD CANNON 14X CANNON 17X AW-LZ17MD9 FUJI NON 36X (A36X14, 5BERD-E28) 5 backward 0 5 backward more than 8 backward 7.5 backward 7 backward Camera Housing AW-CH600 Lic Temporary mounting boss / Arm scale indie Housing p i 5 forward 1 *— "N :ations osition mark / 1 —► i 4 backward 1 1 !® Min1!1 Arm scale V J ■ Connecting to the Housing • Connect the cables from the bottom of the camera housing to the connectors on the panning head, respectively. ND/EXT • How to Connect the Spare Coaxial Cable (Option AW-CA1T1) for SDI Output, etc. Remove the blank panel. Pull out the pin plug and connect it to the receptacle. (Remove panel (A), insert your finger there and pull the pin plug out.) Fasten the receptacle with the removed screw and connect the optional cable AW-CA1T1. { £ C r IpOO. g s—¿Vca To CAMERA -SDI OUT etc. (DAW-CA1T1- p] GOG ‘fjj* Receptacle y ♦ ■ Connecting Cables to the Pan/Tilt Head • Pan/Tilt Control Connector [P/T CONTROL] • The pan/tilt head control cable is connected to this connector. • Connect it to the PAN/TILT CONTROL OUT connector on a control panel (AW-RP301, AW-RP305, AW-RP501, or AW-RP505) or on the multiport hub (AW-HB505). Pin No. Signal Function 1 Dl UP Up control input (Contact signal) 2 Dl DOWN Down control input (Contact signal) 3 DlLEFT Left control input (Contact signal) 4 Dl R...