Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
13 Channel Caption .............................14 Timer Features ...............................14 Sleep Timer................................14 Program Timer .............................15 Set-Up Features..............................16 Set Time...................................16 Antenna (Ant) ..............................16 Auto Prog .................................16 Manual Prog ...............................17 Auto Power On.............................17 CC (Closed Caption) Mode...................17 Instant On Feature ............................18 Control Panel Lock Feature....................18 Troubleshooting Chart ........................20 __Care and Cleaning Picture Tube (Turn set off) Use a mild soap solution or window cleaner and a clean cloth. DO NOT USE ABRASIVE CLEANERS. Avoid excessive moisture and wipe dry. Plastic Cabinets Wipe the cabinet with a soft cloth dampened with water or a mild detergent solution and wipe dry with a soft clean cloth. Avoid excessive moisture. Do not use benzene, thinners or other petroleum-based cleaners. Wood Cabinets When dusting or polishing the cabinet, use a clean soft cloth and stroke straight with the grain. An occasional coat of furniture polish will help preserve the finish. Do not use benzene, thinners or other petroleum-based cleaners. Do not place objects made of plastic or rubber directly on top of the cabinet. A chemical reaction could result causing permanent marring of the finish. Remote Control Transmitter Do not use benzene, thinners or other petroleum-based cleaners to clean the Remote Control Transmitter. To clean, wipe with a soft cloth slightly moistened with a mild detergent and then wipe dry with a soft clean cloth. -5- Installation Monitor Location Locate for comfortable viewing. Avoid placing where sunlight or other bright light (including reflections) will fall on the screen. Use of some types of fluorescent lighting may reduce remote control transmitter range. Adequate ventilation is essential to prevent internal component failure. Keep away from areas of excessive heat or moisture. To insure optimum color purity do not position magnetic equipment (motors, fans, other speakers, etc.) nearby. Optional External Equipment Connections The Video/Audio connections between components can be made with shielded video and audio cables. For best performance, video cables should utilize 75 ohm coaxial shielded wire. Cables are available from your dealer or electronic supply house. Before you purchase any cables, be sure you know what type of output and input connectors your various components require. Also determine the length of cable you’ll need. Power Supply Cord MAKE SURE PLUG IS INSERTED FULLY INTO RECEPTACLE. This product is equipped with a three-wire grounding type plug - a plug with two blades and a third pin which is round. This plug will only fit into a grounding type outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. DO NOT DEFEAT THE SAFETY PURPOSE OF THE GROUNDING TYPE PLUG. Remote Control Battery Installation Batteries: Use two UAA” batteries. 1. Remove the battery compartment cover on back of the remote. 2. Install the batteries in the battery compartment. (Polarity (+) or (-) must be correct.) 3. Reattach the battery cover. Helpful Hints: For frequent Remote Control users, replace old batteries with Alkaline batteries for longer life. Precaution on Battery Use Incorrect installation can cause battery leakage and corrosion that will damage the Remote Control Transmitter. Observe the Following Precautions: 1. Batteries must be replaced as a pair. 2. Do not combine a used battery with a new one. 3. Do not mix battery types (Example: “Zinc Carbon” with “Alkaline"). 4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. 5. Battery replacement is necessary when Remote Control reacts sporadically or stops operating the TV. 3 Wire Ground Plug To Remove Cover Push In And Up On Catch With A Narrow Object -6- Installation (cont.) Antenna/CableConnections Antenna Connection - For CT-1386VY & CT-2086VY only. For proper reception of VHF/UHF channels, an external antenna is required. For best reception an outdoor antenna is recommended. Antenna Mode must be set to TV. (Refer to Antenna Mode section.) Incoming Cable from Home Antenna Indoor Typical VHF/UHF Antenna 75 Ohm VHF/UHF on Back of Set 300 Ohm VHF/UHF on Back of Set or 300 to 75 ohm Matching Trans-former(Supplied 13" Models Only) Cable Connection - For reception of cable channels, connect the cable supplied by your local cable company. Antenna Mode must be set to CABLE. (Refer to Antenna Mode section.) Incoming Cable from Cable Company 75 Ohm VHF/UHF on Back of Set NOTE: Certain cable systems offset some channels to reduce interference or have Premium (scrambled) channels. A cable convert...
Otros modelos de este manual:Vídeo - CT1386YWD (995.03 kb)
Vídeo - CT1386YD (995.03 kb)
Vídeo - CT2086VYD (995.03 kb)
Vídeo - CT2086YD (995.03 kb)