Votos - 2, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Screws Wall-mounting bracket STEP1 Install the wall-mounting bracket onto the wall using the screws. STEP2 Install the camera onto the wall-mounting bracket by referring to the illustration shown on the left. It is possible to install the camera upside down. Install the camera in the upside down position according to your needs. STEP3 Confirm that the Panasonic logo is in the position shown in the illustration. If the logo is upside down, rotate the logo. Logo Note Logo If the camera is placed on a desk, as shown in the illustration on the right, select "Desk top" for "Camera position" on the "Basic setup" page. CONNECTIONS Before starting the connections, confirm which type of connection meets your needs. The following explanations are provided for each connection type. Prepare the required hardware and cables for your connection type before starting the connections. ! Important Before starting the connections, confirm that all the power switches of the camera, the ADSL/cable modem, the switching hub and the PC are turned off, and that all power plugs are not connected to the outlet. Connection between a PC and This Camera (Connection type 1) Connect the camera and the PC directly using an Ethernet cable when browsing the camera pictures or performing the network settings of the camera. < Connection example > AC adapter To an outlet (120 V AC) Ethernet cable (category 5 cross cable) < Required cable > Ethernet cable (category 5 cross cable) ! Important • All cameras connected to the network must use their own exclusive AC adapter. • Use only the specified Ethernet cable, category 5 cross cable. LAN Using with an Intranet (LAN) (Connection type 2) Connect the camera to an intranet (LAN) using an Ethernet switching hub or router when browsing camera pictures of a camera installed in the same LAN (the intranet of a company or home). < Connection example > ! Important • Use an Ethernet switching hub or router suitable for 10Base-T/100Base-TX. • Install also a LAN card suitable for 10Base-T/100Base-TX on the PC. • All cameras connected to the network must use their own exclusive AC adapter. Ethernet switching hub or router < Required hardware > Ethernet switching hub or router < Required cable > Ethernet cable (category 5 straight cable) To an outlet (120 V AC) AC adapter To an outlet (120 V AC) AC adapter CONNECTIONS Using via the Internet (Connection type 3-4) Connecting the camera to the Internet using an xDSL modem or a cable modem. < Connection example > Connection of a single camera Cable modem Cable lineInternet Internet Broadband router Cable modem or xDSL modem (1 port) Cable line or xDSL line AC adapter To an outlet (120 V AC) AC adapter To an outlet (120 V AC) AC adapter To an outlet (120 V AC) Connection type 3 Connection type 4 < Required hardware > • Cable modem or xDSL modem • Broadband router < Required cable > Ethernet cable (category 5 straight cable) ! Important • When the camera is connected using connection type 3 or 4, obtain the global IP address from the Internet service provider. Perform the settings of the camera by connecting the camera and the PC directly. (Refer to the next page.) • When the camera is connected using connection type 3, it is required to assign the global IP address to the camera. When the camera is connected using connection type 4, it is required to assign the global IP address to the broadband router and to set the address translation. (Refer to page 26.). • Use an Ethernet switching hub or a broadband router suitable for 10Base-T/100Base-TX. Install also a LAN card suitable for 10Base-T/100Base-TX on the PC. • All cameras connected to the network must use their own exclusive AC adapter. • To use multiple cameras, it is necessary to set up the router and assign each camera with an HTTP port number. For further information about the assignment of the HTTP port number to the camera, refer to page 28. For further information about the setup of the router, refer to the operating instructions of the router. SETUP After completing the connections, it is necessary to set up the network of the PC and the camera. To operate the camera connected in a network such as a LAN or the Internet, it is necessary to set up the network. Use the provided "Panasonic IP Setup" software to set up the network of the camera. (Refer to the next page). If the setup with the provided software fails, set up the PC and the camera separately. For further information, refer to pages 18 - 28. Preparations for the Setup Prepare the following items before starting the network setup. Ethernet cable (Category 5 cross cable) Ethernet switching hub Ethernet cable (Category 5 straight cable) STEP1 Connect the camera and the PC in either of the ways shown on the left. Use a category 5 cross cable if the camera and the PC are connected directly. ! Important To an outlet (120 V AC) AC adapter STEP2 Turn on the power of the camera after the connection is made. The power is supplied to the camera by connectin...