Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
Insert the mounting base into the hole made in Step 1. 8. Secure the mounting base to the ceiling board with the ceiling board fixing screws (4 positions). q Engage the top of the mounting base with the 1st anchor bolt. w Secure the mounting base by turning the ceiling board fixing screws clockwise. Turning the ceiling board fixing screws clockwise provides ceiling board tightening between the bottom of the mounting base and ceiling board fixing bracket resulting in mounting base securing. (Recommended tigtening torque: 0.78 N·m {8.0 kgf·cm} e Secure the mounting base with double nuts. Important: When securing this bracket on the ceiling, make sure that the four ceiling board fixing brackets are open as shown in the figure. 9. Prepare the cables. Run the cables from the cable inlet. Important: The cables shall be run from the opposite side of the mark, FRONT. Failure to observe this makes the cables unconnectable. 1st anchor bolt Ceiling board fixing screw Ceiling board fixing bracket Insert the anchor boltNut Double nuts Ceiling board Turn clockwise FRONT Cable inlet 10. Install the inner shell. Slide the covers located on the both lateral sides of the camera and put the inner shell on the camera until the hooks inside the inner shell are held in the holes of the camera (until a click is heard). Important: Put the inner shell down on the camera until the outside cover of the camera cannot be seen from the opening (from which the camera lens is visible) of the inner shell. If this integration is not successfully performed, the inner shell may be removed or the hidden part at the top of the screen may become larger in the WIDE mode. How to remove the inner shell Press the inner shell from the front and rear sides inward (at the same vertical position as the hooks) to bend the shell and remove the shell from the camera. Inner shell Hook Put on until a click is heard Cover Press from the front and rear sides inward to bend 11. Mount the camera on the camera mounting plate. q Put the camera onto the camera mounting plate with aligning the lock plate of the camera with the guide of the camera mounting plate and aligning the center of the camera mounting plate with the center of the screw for tripod mounting, and turn the camera clockwise. w Secure the camera with 1 piece of the camera fixing screw (supplied with the camera). (Recommended tightening torque: 0.68 N·m {7.0 kgf·cm}) Important: Be sure to mount the camera with holding the stationary portion of the camera. Camera mounting with holding the rotating portion of the camera may cause trouble. FRONT LOCK Stationary portion Center of the camera mounting plate Camera fixing screw Lock plate Guide Rotating portion 12. Connect the safety wire to the camera. q Connect the safety wire locked on the mounting base to the camera. Make sure that the apical ring of the safety wire is engaged with the safety wire hook of the camera by pulling the safety wire after connection. 13. Connect the cables to the camera. FRONT Mounting base Safety wire Safety wire hook 11 FRON T FRONT F RONT LOCK Projections Hooks for the decorative cover *1 position on the rear side START END FRONT FRONT LOCK Mounting base Camera mounting plate Align A with A Align B with B Fixing screw to be used for cover fall prevention 14. Mount the camera mounting plate on the mounting base. q Align the marks (A to A and B to B) between the camera mounting plate and mounting base. w Mount the camera mounting plate on the mounting base with aligning g of the camera mounting plate with "STARTh" of the mounting base. e Turn the camera mounting plate until g of the camera mounting base aligns with "ENDh" of the mounting base. r Tighten the 3 screws that were removed in Step 2. (Recommended tightening torque: 1.6 N·m {16 kgf·cm}) Important: Do not let the cables be caught during installation work. 15. Mount the decorative cover. q Mount the decorative cover on the camera mounting plate with engaging the projections of the decorative cover with the hooks for the decorative cover. w Turn the decorative cover clockwise while pressing the projections upward and the cover is locked. Important: The mark, "FRONT", shall be aligned with the Panasonic logo. 16. Tighten the fixing screw to be used for cover fall prevention. (Recommended tightening torque: 1.6 N·m {16 kgf·cm}) Note: When the camera lens is pointed in the horizontal direction, the inner shell interferes with the camera’s view, and consequently about upper half of the monitor screen is hidden in the WIDE mode. Specifications Ambient temperature: –10 °C- + 50 °C {14 °F - 122 °F} Dimensions: 185 mm {7-5/16"} in diameter x 145 mm {6-7/16"} in height Weight: Approx. 800 g {1.77 lbs.} Finish: Main body: Treatment steel Decorative cover: ABS resin with silver metallic coating Dome cover: Acrylic resin Standard Accessories Operating Instructions (this book) ............................. 1 pc. The following are for installation Safety wire ..........................