Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
1W) can be connected to the Speaker Terminal (14). E. Other Useful Functions 1. Two kinds of the random operation mode for the Pan/Tilt Head can be selected. Mode-1 : This mode operates like an intermittent auto panning movement. Mode-2 : This is a random panning which is almost impossible to predict a movement of the Panning Head. Refer to item-B of OPERATION on page 10. 2. The setting up of the status for the optional accessories can be displayed on the monitor through WV-CU254. Refer to item-A of OPERATION on page 10. 3. Automatic testing for the optional accessories will be performed by simply pressing a System Test Switch (9)-(SW3). Refer to item-C of OPERATION on page 11. 4. The mode of the relay for auxiliary switching circuit can be set up either a Latch mode or Momentary mode by the Mode Switch (SW2)-(8). Refer to item-B of OPERATION on page 10. 5. The supply voltage for the power zoom lens can be adjusted. Refer to item-F of OPERATION on page 12. C. Videosignal Function The control data is multiplexed on the video signal to perform bi-directional data transmission. -8- INSTALLATION 1. Installation of the Receiver Caution : • WV-RC1 50 is designed for outdoor use. However, install it where the exposure to the rain and the moisture could be minimum as much as possible. • Never install it up-side down. • It is recommended to install WV-RC150 close to the Pan/Tilt Head. • To prevent fire or shock hazard, the UL listed wire VW-1, style 1015, AWG 18 or UL listed power supply cord, type SJT should be used tor the cable for 120V AC Power Terminal (23). (1) Drill four holes for mounting the bolts onto the mounting surface referring the following measurements. (2) Remove the Bottom Plate (17) for wiring through this (3) Make a hole around the center position of the Bottom Plate (17). The diameter of the hole should be calculated with the bunch of the cables which is to be conducted through this hole. (4) Mount the Receiver with four mounting bolts. (To be local procurement.) (5) Open the cover and make a necessary wiring with terminals through the Bottom Plate (17). (6) Be sure to secure all cables to the Cable Clamping Angle (16) with a Cable Clamp (provided). (7) After complete the wiring, be sure to proof against the water at the wiring hole. Note : When WV-CA50, the prewired cable with a rubber bushing, is used for wiring, remove this rubber bushing from the cable and do not utilize it for the waterproof purpose. 2. Installation of the optional Audio Borard (WV-PB10) (1) Turn off the power of the Receiver. (2) Remove three screws of the circuit board-A. (See Fig. 1.) (3) Insert the connectors of WV-PB10 into the connectors on the circuit board-A. (See Fig. 2.) (4) Fix the circuit board-A with WV-PB10 back on the chassis with three screws. (5) Fix WV-PB10 with two screws. (See Fig. 2.) (Fig. 1) Board-A Fix WV-PB10 (Fig. 2) Caution: The electrical parts on the back of the circuit board should not touch the chassis when re-install the circuit boards. 3. Installation of the prewired cable WV-CA50 (1) Connect the BNC connector of WV-CA50 to the Camera Input Connector (2) of WV-RC150. (2) Connect the prewired connectors, 12 pin and 14 pin, of WV-CA50 to the Prewired Cable Connectors (19), (20) of WV-RC150. -9 - OPERATIONS A. Active/Non-Active Switch (SW1)-(10) B. Mode Switch (SW2)-(8) There are eight individual switches in SW1 and is corresponding to each input function. In case that any of these switches is turned to ACTIVE position, its function will become active status. On the contrary, when the switch is turned to NOT ACTIVE position, its function will not work even if the product is hooked up with WV-RC 1 50. These status will be displayed on the monitor -TV through WV-CU254. • Switch 1 (AUX2): For the product of Aux-2 • Switch'2 (AUX1): For the product of Aux-1 • Switch 3 (AUTO PAN): For the Panning Head which has an Auto Pan function. • Switch 4 (RESERVED): This switch is for the future function and should be in the off position all the time. • Switch 5 (CAMERA AC): For the power supply for the 24V AC camera. • Switch 6 (DEF): For the power supply for the Defroster on the camera housing. • Switch 7 (WIPE): For the power supply for the Wiper on the camera housing. • Switch 8 (RESERVED): This switch is for the future function and should be in the off position all the time. There are. three individual switches in SW2 and is correspond to each input function. The SW2 is a switch for selecting the mode of the function. SW2 RANDOM PAN MODE I AUX2 MOMENTARY AUX1 MOMENTARY -□ MODE] ~dn LATCH LATCH 1. Switch 1 (RANDOM PAN/MODE2 - MODE1) For the selection of MODE1 or MODE2 of the Random Panning function. (1) MODE1 • This mode operates like an intermittent auto panning movement. • Turn the Power ON/OFF switch (1) on while pressing the System Test Switch (9). The panning head moves to right (or left) for a pre-adjusted time. Then it s...