Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
Before initializing the settings, it is recommended to write down the settings in advance. FOCUS ASSIST Tilting lock screw INITIAL SET button SDHC/SD memory card slot Focus assist (F.A.) button Access indicator (blinking at accessing) Link indicator (lighting at linking) SDHC/SD memory card error indicator/F.A. indicator (Lights when the focus assist function is activated or when the focus ring is positioned near the best focus position) SF335 SF332 SF335 SF332 AF Auto focus (AF) button SF336 SF336 SDHC/SD memory card error indicator/AF indicator (Blinks when AF is being adjusted) FRONT TOP EXT I/O AUDIO OUT MIC/ LINE IN 10BASE-T/ 100BASE-IX 4 2 3 1 MONITOR OUT F N Audio output connector Microphone/line input connector Network connector Lens External I/O terminals Zoom lock knob Focus lock knob SF335 SF336 F N Detaching the dome cover Detaching the dome cover Important: • After removal, retain the dome cover fixing screw so as not to lose. The screw is required when attaching the dome cover. (. Page 34) • Remove the cover film from the dome section of the dome cover after the installation is complete. Do not touch the dome section by hand directly after removing the cover film. z Remove the dome cover fixing screw (M3, step screw, x1). LOCK ADJUST OPEN Dome cover fixing screw (M3, step screw) x Rotate the dome cover counterclockwise two steps, and align the indication "OPEN" to the maker of the camera to detach the dome cover. OPEN Marker ADJUST OPENLOCK Dome cover Dome alignment indication "OPEN" Dome section Preparations Preparations When installing the camera on a wall or a ceiling, there are four methods as specified below. (. Pages 20 and 21). • Using the two-gang junction box • Installing the camera directly on the ceiling or wall • Using the optional ceiling mount bracket WV-Q168 (for embedded installation on a ceiling) • Using the optional ceiling mount bracket WV-Q105*1 (for direct mounting on a ceiling) Important: • Procure 4 screws (M4) to secure the camera to a wall or a ceiling according to the material of the installation area. In this case, wood screws and nails should not be used. For mounting a camera on a concrete wall, use an anchor bolt (for M4) or an AY plug bolt (M4) for securing. (Recommended tightening torque: 1.6 N·m {1.18 lbf·ft}) • Required pull-out capacity of a single screw/bolt is 196 N {44 lbf} or more. • If a ceiling board such as plaster board is too weak to support the total weight, the area shall be sufficiently reinforced or the optional ceiling mount bracket for the camera, WV-Q105, must be used. The mounting conditions of the camera are described as follows: Installation Applicable mount Recommended Number of Minimum pull-out place bracket screw screw strength (per 1 pc.) Ceiling/wall Two-gang junction M4 4 pcs. 196 N {44 lbf} box Ceiling/wall (Direct mounting) M4 4 pcs. 196 N {44 lbf} Ceiling WV-Q168 (approx. – – *2 280 g {0.8 lbs}) Ceiling WV-Q105*1 (approx. – – *2 150 g {0.8 lbs}) *1 PAL models only *2 Make sure that the installed mount bracket can support more than 5 times of the weight of the camera. Using the side cable access hole When installing the camera directly on the ceiling or wall with cables exposed or when using the optional ceiling mount bracket WV-Q168, cut out a portion of the dome cover to open a cable access hole. Side cable access hole Side cable access hole Method of camera installation Using the two-gang junction box Mount the camera on the two-gang junction box by fixing 4 screws (locally procured). (. Page 28) FRONTTOPEXT I/O AUDIOOUT MICLINE IN 10BAS100BA 12V=IN 4 2 3 1 MONITOROUT N F Direction marker for installation Two-gang junction box (locally procured) Screws 21 Installing the camera directly on the ceiling or wall Place the installation template label (accessory) on the ceiling or wall, and make a hole to pass the cable. Remove the template label, and mount the camera by fixing 4 screws (locally procured). (. Page 28 ) FRONT TOP EXT I/O AUDIO OUT MIC LINE IN 10BAS 100BA 12V=IN 4 2 3 1 MONITOR OUT N F 20 mm {13/16"} 83.5 mm {3-5/16"} Direction marker for installation Cable access hole for ceiling/wall Recommended screw (M4: 4 pcs.) Side cable access hole Screws (locally procured) Installation template label (accessory) 46 mm {1-13/16"} 40 mm {1-9/16"} Using the optional ceiling mount bracket WV-Q168 It is possible to reduce the exposed portion of the camera body using the optional ceiling mount bracket. Refer to WV-Q168 Operating Instructions or "Installation" (. page 28) for how to mount the camera. Using the optional ceiling mount bracket WV-Q105 (PAL models only) Refer to WV-Q105 Operating Instructions and "Installation" (. page 28) for how to mount the camera in case of using the optional ceiling mount bracket. Anchor bolt Safety wire angle Roof space Safety wire Camera WV-Q105 (option) (4 pcs, WV-Q105 supplied) Cable tie (accessory) Ceiling board such as plaster board Insert/remove an SDHC/SD memory card Insert/remove an SDHC/SD me...