Votos - 4, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Vídeo - VB-H610D (15.44 mb)
Vídeo - VB-H610D (346.3 kb)
Vídeo - VB-H610D (979.72 kb)
Resumen del manual
Screwdriver Tightening torque: 0.2 N·m (max.) Strip Approx. 4 to 6 mm (0.16 to 0.24 in.) Power connector (included) For 12 V DC and 24 V AC input, use a power supply insulated from 100 V AC. 12 V DC can be connected in a non-polar configuration. Important • The power supply should be within the following voltage range. • 24 V AC: Voltage fluctuation within ±10% of 24 V AC (50 Hz or 60 Hz ±0.5 Hz or less) Current supply capacity of at least 1.0 A per camera • 12 V DC: Voltage fluctuation within ±10% of 12 V DC Current supply capacity of at least 1.5 A per camera • When using a 12 V DC battery power supply, be sure to connect resistors of at least 0.5 – 1.0 ./20 W in series to the power line. • For an external power supply, use a double-insulated device. Recommended Power Cables [Reference] Cable (AWG) 24 22 20 18 16 Conductor diameter mm (in.) 0.52 ( 0.020) 0.65 ( 0.026) 0.82 ( 0.032) 1.03 ( 0.041) 1.30 ( 0.051) 12 V DC maximum cable length m (ft.) 5 (16.4) 9 (29.5) 14 (45.9) 23 (75.5) 32 (105.0) 24 V AC maximum cable length m (ft.) 11 (36.1) 18 (59.1) 29 (95.1) 46 (150.9) 64 (210.0) Use UL cable (UL-1015 or equivalent) for 12 V DC or 24 V AC wiring. . AC Adapter Use the dedicated AC Adapter PA-V17 (sold separately). Note • The camera does not have a power switch. Connecting and disconnecting the LAN cable (PoE power supply), AC adapter, or external power supply plug turns the power ON and OFF, respectively. • When the camera needs to be rebooted, perform the reboot operation from the camera setting page (see “Operation Guide” > “Setting Page” > “Maintenance”). • When using the heater unit HU600-VB (sold separately), use 24 V AC for the VB-H610VE/VB-M600VE power supply. PoE, 12 V DC and the AC adapter cannot be used. External Device I/O Terminals External device I/O terminals consist of two input and output systems each. Viewer can be used to check external device input status and control output to an external device (see “Operation Guide” > “Selecting the External Device Output” and “Displaying Event Status”). . External Device Input Terminals (IN1, IN2) External device input terminals consist of two sets (IN1, IN2) of two terminals, with the negative terminals connected to the camera interior GND. Connecting cables to the positive and negative terminals and opening or closing the circuit notifies the Viewer. Important • When connecting sensors and switches, connect terminals that are electrically isolated from the respective power and GND. • Do not push the external device I/O terminal button with too much force. Doing so may cause the button to remain pushed-in. Using a Junction Box Use the junction box plate (included with the separately sold junction box mounting kit PS600- VB) to mount the camera to the junction box. 1 Attach the junction box plate to the junction box with screws that match the screw holes in the junction box. 2 Guide the cables through the wiring hole and mount the camera to the junction box plate using the 3 included camera fixing screws (M4). The camera fixing screws differ in length depending on the camera. Use short screws for VB-H610D/VB-M600D, and long screws for VB-H610VE/VB-M600VE. 3 Wire the cables and attach the inner cover and dome case. * Diagram of VB-H610VE. Using an SD Memory Card Inserting the card SD card slot Push the SD memory card as far as possible into the SD card slot with the label facing outward. Removing the card Push the SD memory card in all the way until the card slightly pops out. Pinch the card and remove. Important • Insert the SD memory card before attaching the dome case. • Make sure the SD memory card is not write-protected. • When using an SD memory card with the camera for the first time, it is recommended to format the card after inserting it into the camera (see “Operation Guide” > “Setting Page” > “Memory Card”). Junction box plate Camera fixing screw (included) Short screw x 3 Long screw x 3 Dome case fixing screw x 3 . External Device Output Terminals (OUT1, OUT2) External device output terminals consist of two sets (OUT1, OUT2) of two terminals. The sets have no polarity. Controls from the viewer can be used to open and close the circuit between the terminals. Using optical couplers, the output terminals are isolated from the camera's internal circuit. Internal Connection Diagram Internal controller External device Input terminal IN1, IN2 Output terminal OUT1, OUT2 +3.3 V 0.1 .F 10 k. 10 k. 1 k. External device . The load connected to the output terminals should be within the following rating range. Rating between output terminals: Maximum voltage 50 V DC Continuous load current at or below 100 mA On resistance: Max. 30. Note Adaptive wiring for external device cables Solid conductor AWG: No. 28 – 22 Conductor size: 0.32 – 0.65 mm ( 0.013 – 0.026 in.) Cable strip should be approx. 8 – 9 mm (0.31 – 0.35 in.). Audio Input/Output Terminals Each audio input/output terminal has one input system and one output system. Connecting the camera to an au...
Otros modelos de este manual:Vídeo - VB-H610VE (7.88 mb)
Vídeo - VB-M600D (7.88 mb)
Vídeo - VB-M600VE (7.88 mb)