Iniciar sesión:
Votos - 2, Puntuación media: 3 ( )

Manual de usuario Crimestopper Security Products, modelo WIRELESS RECEIVER WR-3000

Fabricar: Crimestopper Security Products
Tamaño del archivo: 51.23 kb
Nombre del archivo: 46b03991-61cd-4471-a636-ba1308ab475f.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


This device may not cause harmful interference. 2. This device must accept any interference, including interference that may cause undesired operation. INTRODUCTION The WR-3000 receiver can be used with any of the Dakota Alert 3000 series transmitters ( WMT-3000, WPT- 3000, WHT-3000) . The WR-3000 plugs in to a standard wall outlet and can be placed on a table or mounted on the wall. When the receiver gets a signal from the transmitter one of 4 different tones (Classical , Westminster Chime, Ding Dong, Whistle) will sound for a few seconds. There is also a volume control so you can set the sound to the desired level. The receiver is also equipped with 4 form “C” relays (one for each zone) and one 12 VDC output terminal that will activate for several seconds when a signal is received. The receiver can be user programmed so the 12VDC terminal and one relay will activate for 10 minutes if this is desired. The tones will still sound for several seconds. 2. OPERATION 1. Connect the end of the power supply to the receiver. (1) 2. Plug the power supply into a wall outlet 3. Locate the off/on switch (2) and move to the “on” position. 4. Press the “test” button (3) on the side of the receiver to determine the level of the volume. Rotate the “volume” knob (4) until you have the sound desired level. WR-3000 Receiver Transmitter Module 2 3 1 4 5 8 } } 6 7 3. For maximum range between the transmitter and receiver, the receiver should be mounted horizontally on a wall and as high off the fl oor as possible. Although the maximum range is about 3000 feet, things such as hills, trees, metal siding and stucco can all reduce the range. CODING THE RECEIVER 1. Open the receiver case by inserting a small screw driver into one of the pry notches on the side of the case. 2. Gently lift off the front cover. 3. Locate the 8 dip switches (5) on the receiver and make sure they set identically to the first 8 dip switches (6) on the transmitter. Note: If more than one transmitter is used with the receiver, the first 8 dip switches of all transmitters must match the 8 dip switches of the receiver. NOTE: Whenever a change is made to the time jumper or the dip switches, the receiver must be turned “OFF” and then back “ON” to operate properly. CODING THE TRANSMITTER 1. Locate the dip switches in the 3000 series transmitter. (refer to transmitter manual) 4. 2. The first 8 dip switches (6) are for the frequency setting (256 combinations). Set the first 8 switches to match the 8 switches in the receiver. 3. Switches 9 & 10 (7) are for the zone/channel setting on the transmitter. The four zones are as follows: Switch 9 Switch 10 Channel Tune ON ON 1+12VDC Classical OFF ON 2 Westminster ON OFF 3 Ding Dong OFF OFF 4 Whistle TONE, RELAY AND VOLTAGE OUTPUT 1. Each of the four transmitter zones (selectable by switch 9 & 10) will sound a tone and activate the corresponding relay on the receiver. 2. Each of the form “C” relays is rated for 24 VDC at 3 Amp maximum current. 3. The 12 VDC outp...

Otros modelos de este manual:
Vídeo - WIRELESS RECEIVER WR-3000 (51.23 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría